There is nothing sadder than looking at the magnificent retina display new model iPhone smartphone through a giant scratch running through the center of the screen. Apple guarantees the high strength of the glass used in the iPhone, but it can still break and scratch. How can the risk of such unpleasant incidents be reduced? After all, removing a scratch from the glass is almost impossible. It is best to take care of your pipe in advance and stick on iPhone protective film.

Below are instructions on how to install an Epic screen protector on iPhone 5. You can use the above recommendations for films from other manufacturers.

1. Unpack the protective film

Carefully open the paper or plastic packaging with the protective film. In paper packaging, simply tear off the "open" strip.

2. Clean the iPhone screen

Using a microfiber cloth (often included with a protective film), carefully clean the smartphone screen. It should be free of dust and fingerprints.

This is a very important step, and its implementation should be approached with all responsibility. After the protective film is pasted, it will be impossible to remove the dirt under it.

3. Trying on

Before removing additional elements screen protector, make sure it fits the iPhone screen size well. Start from the bottom edge. Position the film so that the notch on it neatly surrounds the home button. You should also follow the correct positioning of the hole opposite the speaker and how neatly the edges and corners of the film are located.

The cut of the top edge must not overlap the ambient light level sensor.

Slight deviations from the ideal film position are acceptable. They will not interfere with the operation of the device, and will be almost invisible during its operation.

4. Start sticking

Holding the protective film in one hand, we pull the tab, which is usually marked with the number "1" or the inscription "Step 1". We release the most upper part protective film from an additional element.

5. Starting at the Top

We begin to stick the film from the top edge. Gently lay the topmost part of it on the glass surface. We check how accurately the corners lie at the intended points. After that, we press the film to the screen so as not to move it.

6. Top down

With one hand, we gradually remove the additional film, and with the other, carefully and slowly place the protective film on the screen, making sure that its edges lie parallel to the edges of the case.

After that, we begin to remove the lower additional film. After a minute or two, the protective film will be completely fixed on the front surface of the iPhone.

7. Remove Bubbles

Using a special rubber tool, usually included with the film, we remove air bubbles from under the protective film. We “drive” the bubbles to the edge and release them “to the wild”.

However, not all bubbles will "want" to be removed. It's okay, within a day they should disappear on their own, leaving no traces.

8. "Burning Bridges"

If the protective film is located as intended, then remove the second tab at the top of the screen. It is usually labeled "2" or "Step 2".

So we installed a protective film on the front surface of the iPhone 5!

9. Protective film on the rear window

In a similar way, you can protect the rear glass of the smartphone.

10. How to remove dust from under the iPhone 5 protective film

If a speck of dust is found under the protective film, then you should use a small strip of ordinary stationery tape. Stick it to the edge of the protective film closest to the speck of dust and gently lift it up.

11. We catch a speck of dust

With the help of the second piece of adhesive tape, we “capture” the dust speck and remove it from the screen surface.

After that, carefully return the protective film to its place.

Now we can not be afraid of scratches on the screen of our iPhone 5.

Screen protector is the cornerstone. It seems to many that it is simply impossible to stick it normally, especially on your own. Others calmly do it with their own hands and are in the status of the owners of "secret knowledge". But in fact, it's really quite simple: you just need to learn a few secrets.

The brief instructions that usually come with the film, as a rule, turn out to be useless. Who came up with the idea to write the cherished “Paste the film evenly and without bubbles” is unknown, but this “someone” clearly did not know about the difficulties and suffering that accompany this process. Try putting the instruction aside and doing something else.

First, wipe the screen of your smartphone with an alcohol wipe or microfiber. And do not spare time and rub carefully so that not a single microbe remains on the screen. Now life hacks. The first secret is to fix the film on the screen before you peel off the protective layer. This minimizes the possibility of dust getting under the film before gluing. Yes, and it will be more convenient to work.

Put the film on the phone and fix it around the edges with tape, leaving one side free. Lift the film by the free edge and carefully peel off the protective layer.

The main thing to try to avoid is the ingress of dust and the formation of air bubbles. Therefore, stock up on a credit or any other plastic card before gluing the film. Help yourself with this “tool” by pressing the film firmly while gluing. Smooth it with a card and make sure that air does not penetrate under the coating. If the dust is still under the film - do not peel it off! Secret number two: instead of re-pasting everything, move the dust to the very edge of the film, firmly pressing the edge plastic card to the screen.

Protective film for the iPhone is the first thing every new owner should think about. this device. With quality film iPhone screen protects against cuts from keys in your pocket, scuffs from not very careful handling, for example, when the iPhone is placed on the table with the screen down, as well as from fingerprints. The film allows you to keep the display of the device in its original form, which is not only pleasant during use, but also helps to profitably sell the device.

Films for the iPhone are different, but they differ only in their quality and coating material. The gluing process is the same for all films, so we will not consider models of films from different manufacturers, but we will still tell about the material covering the top layer of the film.

There are three main types of iPhone screen protectors:

• matte - easily cope with glare on the screen. Ideal for use in constant bright sunlight
• glossy - improve the picture of the iPhone. Images on the screen when using such protective films will become brighter and more contrast.
• mirrored - give the iPhone display a very beautiful appearance

These are the three main categories of iPhone screen protectors. Additional properties, such as self-healing or antibacterial coating, are just bells and whistles that manufacturing companies build into their films, giving them more value.

The film has been chosen, it remains only to stick it correctly. In some stores, employees may offer you help in applying a protective film and it is better not to refuse it. An experienced specialist will paste the film perfectly evenly and will not spend much time on it. If such an offer has not been received, you can inquire about providing you with such a service. But if suddenly you find yourself at home with an unpacked protective film in your hands, gather your thoughts and proceed to this simple but painstaking process.

How to stick a film on an iPhone

Step 1: Unpack the protective film. The package of any film for the iPhone includes the protective film itself, a microfiber cloth and a special device for removing bubbles from under the film (can be plastic or rubber)

Step 2: Clean up iPhone display. This must be done with the included microfiber cloth. Carefully, in a circular motion, remove all greasy traces and dust particles from the device screen - the better you clean the screen, the better your iPhone will look after sticking the film

Step 3. Try on the film on the iPhone screen. It's too early to pull the labels pasted on the film - first you need to make sure that the film fits in size and figure out the plan according to which you will glue it. Try to navigate by the Home button and the speaker cutout, this will allow you to stick the film as accurately as possible

Step 4. Let's start sticking the protective film. Hold the film in one hand and pull the tab with the number 1 on it (may also be written Step 1. Remove me!). By removing the first layer of film, you will “bare” the adhesive surface, so be careful! In no case do not put the film on the table and in general it is better to try so that dust does not get on the sticky surface

Step 5. We begin to glue the film. Start sticking the film on the top edge of your iPhone. Focusing on the side edges and the speaker connector, evenly attach the film to the glass surface. Attention! If the first time the film lay unevenly, it's okay. Carefully peel it off the surface and try to stick the film again - the film will not lose its adhesive qualities even after several such failures, but you should not abuse it

Step 6. We glue the film. Apply the protective film lower and lower, at the same time, slowly, smoothing the area to be glued. Try not to make sudden movements, otherwise you risk planting a bubble that will not be so easy to remove. Make sure the film is laid parallel

Step 7. Remove the bubbles. After the film is completely glued, do not rush to remove the second protective layer. Armed with the bubble remover that came with the kit, gently begin to push the bubbles towards the edge of the screen. Try to achieve the maximum result - most likely you will have to spend some time on this. Attention! Do not forget to go separately to the place where the second label is located

Step 8 Remove the second protective layer. While holding the film, pull the last remaining label and remove the entire top protective layer. It is necessary to hold if the film does not lie firmly enough, but it is better to play it safe.

After removing the film, you can proudly see the result of your work, we hope that you will be able to stick the protective film on the iPhone evenly and without an impressive bubble size. However, bubbles are not the worst problem, dust particles are much more significant.

How to Remove Dust from Under iPhone Protective Film

Step 1. Take stationery tape (its narrow version) and cut off a small piece. Stick the adhesive tape to the place as close as possible to the dust and gently lift the protective film. Protective films sometimes come with specially prepared pieces of adhesive tape, which you can use in this situation.

Step 2. After lifting the film, do not lift it very high so that new foreign objects do not get under the film. With the second piece of tape, carefully hook the hated speck of dust. Attention! Do not try to cling to a speck of dust with tongs or other sharp objects - you risk scratching the protective film.

Step 3. After removing the dust, slowly return the film to its place, smoothing out the bubbles that appear

In the same way, unintentionally fallen hair and other foreign objects can be removed from under the protective film. The process of applying the iPad screen protector is the same as above, but requires much more concentration due to the large screen area. The protective film on the back cover of the device is glued using a similar technology.

Also interesting:

• How to turn off bluetooth on iPhone?
• The Way to Increase iPhone Battery Life Everyone Forgets About
• Internet Beeline on iPhone

Please rate 5 stars at the bottom of the article if you like this topic. follow us

Whether it is necessary to glue the film on your smartphone is a moot point. On the one hand, it impairs visibility, thereby increasing the glare from the sun, but on the other hand, it supports the screen of your gadget

How to stick a protective film on an Apple iPhone?

Whether it is necessary to glue the film on your smartphone is a moot point. On the one hand, it impairs visibility, thereby increasing the glare from the sun, but on the other hand, it maintains the screen of your gadget in its original form. So if you are thinking about selling your device, after you get tired of it and change it to a new one, then this issue has been resolved - you need to glue it. In this article, we will tell you how to properly stick a protective film on your iPhone yourself.

First you need to put the iPhone under the lamp daylight(fine dust particles and villi become visible) and wipe its screen to make sure that there are no fingerprints, grease, dust particles or traces of any other dirt before sticking the film. Especially - so that there are no solid particles on the screen. To do this, you need to use a special cloth (microfiber). It usually comes with a protective film. Why you can take water or spray to clean LCD monitors. This is usually sold in computer stores. Do not use alcohol-based household products. Or, even more so, the alcohol itself! It's bad for the screen!

How to glue a protective film on iPhone 4

Read also

How to glue protective film on iPhone 4 .

How to glue a protective film on iPhone 4 video tutorial

Not expensive Chinese film, but good quality. In the second part we glue film on the back cover and remove ...

Read also

After cleaning the screen, carefully remove the film from the package. Look at her carefully. There are 2 stickers attached to the corners. They are paper. Lay the film on a flat, clean surface. Next, you need to press the stickers if they were not particularly tightly fixed. Then we begin to peel off only a small edge of the shipping film, a little more than a square centimeter. Do not touch the sticky part of the film. It is better to do this not with your hands, but with a sticker, since there are fewer traces left this way.

Next, you need to align the corners of the film - and correlate them with the corners of the screen surface, you need to press the free edge of the film - to the screen itself. Well, if you notice that the film lay rather crooked, then you can peel it off and start over. The advantage of films of this kind is that such manipulations are quite calmly performed repeatedly. The adhesive surface does not lose its properties immediately. However, you should not abuse this, as crumbs, dust, and so on can get on it. And in this case, it is better to throw away the film.

Read also

If you, after pasting the first part, found bubbles, then you do not need to worry. Air can be removed. To do this, you can take any plastic card, gently hold it from the center of the screen to the edges. The bubbles will disappear.

A mobile phone is a fragile device that gets scratches and so on over time. This significantly spoils its appearance. He becomes unsightly and unkempt. And many people know that a lot can be said about a person by looking only at his phone. Therefore, for many, the problem of protecting the phone from mechanical influences and other things that worsens its external data is acute.

She has a solution. It is enough to use auxiliary devices. For example, a cover. He is able to protect as one certain element device, and its entire from scuffs and other damage.

Protective film on the screen: main functions

One such method is the application of film to the screen. It protects against scratches, abrasions, etc., which cannot be avoided even with the most careful attitude to the device. And it doesn't matter who made it. Even the most famous and popular Apple company recommends using a screen protector, as it will allow you to keep the original appearance of the product for a very long time. Although there is one drawback with this product - the film reduces the quality of visibility. It is worth noting that it is insignificant, and in principle, the human eye is not able to perceive the differences when it is on the screen, and when it is not.

How to glue a film on an iPhone: who to trust?

Gluing a film on an iPhone is not easy. This is a painstaking work that requires care and accuracy. IN otherwise bubbles appear on the screen. They spoil its appearance and testify to the poor quality of this work.

Basically, the film is glued by the specialists of the store where the goods are purchased. But you will need to pay separately for this. The cost of this service is equal to the price of the film. In this case, the specialist is responsible for it. In case of poor performance, you can demand that they redo it. And everything must be done at their expense.

If you decide to save money, you can stick the film on the iPhone yourself. But it is better to initially calculate your strength. Will you be able to do it. As practice shows, if you do it carefully and know the features this process, then its implementation is within the power of everyone.

How to properly glue a film on an iPhone: preparatory measures

To stick a film on an iPhone, no special equipment or tools are required. Therefore, you can do it at home. The first thing to start with is to put the phone on the table. Then point a lamp at him. Better if it is daylight. This will determine if there are dust particles and lint on the screen.

Then you need to wipe it with a microfiber cloth that comes with the phone. You can do this with a special spray that is used to clean such devices. But it must be purchased separately. It is in many stores that sell computers. For this purpose, it is strictly forbidden to use products that contain alcohol, as this will be harmful to the screen of the device.

Make sure the screen is clean. It should be free of fingerprints, grease stains, dust and other dirt. Particular attention should be paid to the presence of solid particles. They are extremely unsafe for the screen.

After completing these works, you need to get the film that is in the package. This is done carefully so as not to damage it. Then you should take a good look at it. So, on its corners there are stickers that will be used.

How to properly glue a film on an iPhone: process features

To start working with the film, it is placed on the table. At the same time, its surface must be dry, even and clean. The paper stickers are loose and easy to peel off. But it is worth paying attention that this is done by a centimeter. Moreover, you cannot touch the adhesive side of the film with your hands. Thus, stains and other unwanted marks may remain on it.

Then the film is applied to the phone screen. At the same time, clarity is important. Therefore, the corners of the two surfaces must match. Next, the free edge of the film is well pressed against the screen. If on initial stage irregularities appeared, it is better to remove the film and start all over again, since it will be problematic to do this further. This manipulation can be carried out several times until the desired result is achieved. At the same time, it will not deteriorate in any way and will not lose its appearance. But you can’t overdo it, as dust and other dirt can get on it. The adhesive side of the film grabs them quickly. If this happens, then it becomes unsuitable for further use. Therefore, it is better to throw it away and take a new one.

After that, the entire film is glued. In this process, bubbles appear quite often, even for professionals who do this work daily. Do not worry - this situation can be corrected. They can be removed using a plastic card - it is swiped across the phone screen, and this must be done from the center to the edge. This simple procedure will get rid of all bubbles and unwanted air under the film.

The final step is the removal of the second film, which acts as an auxiliary. And it's better to do it with a sticker. But it must be the second.

Do I need to glue the film on the iPhone?

Do I need to glue the film on the iPhone? This is one of the most frequently asked questions. Since everyone knows about the high quality of this product. But, as practice shows, it is necessary to glue the film on any screen. And it doesn’t matter if it’s a phone or a tablet, as you will carry it in your pocket, purse or other place. At the same time, it can be rubbed, scratched, which will spoil its appearance. After a year of operation, it will change. This is an unwanted effect. Only a protective film will help protect the iPhone screen. And only you will know about its existence. To identify an outsider, you need to look closely, it is unlikely that he will do this. The film is transparent, so the design and other data of the phone will remain unchanged.