Samsung galaxy s7 replica firmware. Samsung galaxy s7 firmware Chinese

Instructions for installing the official single-file firmware on samsung galaxy S7 (SM-G930x).

Drivers and programs

Attention!

To install the official stock firmware on Galaxy S7 and return the phone status (Settings > About device > Properties > Device status) to "Official" after switching from custom firmware and thus return the possibility of receiving updates over the air, it is enough to follow the instructions presented.

Installation instructions

Unzip the downloaded archive to a folder with Odin PC for convenience. The file in ".tar" or ".tar.md5" format must be left, but "SS_DL.dll" can be deleted.

Perform a data reset on the device.
To do this, go to the settings in the section " Backup and reset settings”, select the item “ Data reset» > « Reset device”, enter the PIN code (if one is set) and press the button “ Delete everything". The phone will reboot.

Run Odin PC as administrator.

Put the device into download mode ( Download Mode).
To do this, simultaneously hold down the Volume Down key, the Home button and the Power button. Then wait until the phone reboots and agree to the warning by pressing the Volume Up key.

In this state, connect the smartphone to the computer. In Odin, the inscription " COM».

Click on the button " AP» and select the TAR archive of the firmware.

Items « Auto Reboot" and " F.Reset Time" must be activated, a " Re-Partition", if active - must be disabled.

Click on the button " Start". The firmware installation process will begin.

At the end of the operation, if everything went well, the message “All threads completed. (succeed 1 / failed 0)". The phone must be rebooted manually by holding down the power button until the screen turns off. The initial boot of the device may take up to 5 minutes.
ATTENTION!
If the device does not boot long time or a data reset was not made, it must be performed from the recovery.
To do this, simultaneously hold down the Volume Up key, the Home button and the Power button. After downloading select " Wipe data/Factory reset", and then - " Reboot system now". If after these steps the device also freezes at boot, you need to reflash it again.

Often, many of you are faced with the fact that your phone, which served you faithfully, and suddenly began to slow down, stopped working properly, or caught a serious virus that could not be got rid of.

Then make yourself comfortable, now we will tell you how to get rid of all these problems with your phone by flashing its operating system.

If this program does not work on this device, you can try to backup your data with official program for archiving Samsung data " ".

Attention!!! We have to warn you that flashing a smartphone is a very serious and dangerous process, and if you do something wrong, your smartphone can turn into a brick. WE ARE NOT RESPONSIBLE for all your manipulations with your smartphone, everything you do you do at your own peril and risk, it all depends on how straight your hands are.

If you are not sure that you can perform this procedure, contact a specialist.

Firmware Samsung S7 Edge through the ODIN program

So we will divide our whole process into several stages:

Disable Remote Control

Before you start the firmware, you will need to disable the device activation lock in the phone settings, if this is not done, the process may fail. In new Android devices this feature is called "Remote control".

• So we need to go to the "Settings" window, then - "Lock screen and protection".

• Next, we need to go to the "Find phone" subsection.

• Here we authorize using the data account Samsung.

• In this section, disable the "Remote control" option.

Install original drivers from Samsung on PC

So at this stage, we will need to install the original Samsung drivers for mobile devices.

If you already have these programs installed, then it will not be superfluous to double-check for updates. Before installing the drivers, connect your smartphone to the PC. After you have installed the drivers, restart your PC.

Checking for correct installation and operation of drivers

Connect the cable to the phone and if the PC recognizes your phone, then everything is installed correctly. If the computer does not see the phone from the original cable, then try changing the cable.

Download firmware

Download the firmware on a PC and unpack the archive. Regarding what firmware to download, we cannot tell you, you need to look at the version of your firmware in the settings of your smartphone, you can see the entire set of firmware -

Download the ODIN Flasher

For firmware you will need to download the program " ODIN" in which you will flash your smartphone, for S7 Edge, download the version "ODIN" at least 3.12 -

Important!!! never download the russified version" ODIN"- this will turn your smartphone into a brick. Next, unpack the archive and run the program.

Try to unpack the firmware files to the root of the disk. Launching ODIN Unpack the file with the flash driver and run the "ODIN" program.

Activate bootloader mode

Turn off the smartphone using the "Power" button:

• We press and simultaneously hold 3 buttons: "Home", "Volume down" and "Power".
• We are waiting for the image to appear on the screen of our device.
• Release all buttons.
• Press the "Volume Up" button once.

We connect our smartphone to the PC

Go back to the Log tab and connect the files of the downloaded firmware in the specified order:

1. BL > put the file BL******tar.md5
2. AP > put the file AP******tar.md5
3. CP > put the file CP******tar.md5
4. CSC> put the file CSC*****tar.md5

Starting the firmware process

Completing the download process

When the download is complete, a "PASS!" notification will appear to indicate that the download process is complete. After that, the smartphone will reboot automatically. Disconnect the cable and wait for the smartphone to reboot

Yes, any master will say that real Chinese phones work great. Firmware S G S7 S G920 Chinese. What official firmware are you currently using? Chinese and Korean copy Galaxies are copied to the smallest detail, to the naked eye of them. It will help you to flash Chinese S G. Firmware Chinese phone 7 added new file. Firmware S G S7 clone, flashing Chinese copy. S SMG930F G S7 Official Firmware

Chinese Copy S G S7 Firmware M6571. Firmware for Chinese S G S7. Chinese copy 7 firmware. Please go to the direct link to download firmware version G930FXXU1DQD7 for S G device. Update S S G S7 phones update and firmware. Firmware S G S7 S G920 Chinese If you bought a quality knockoff, you will need a copy of S G S6 SMG920F firmware. If you still decide to update the S G S7 firmware, then you must accept all the consequences and the possibility of obtaining non-working smartphone from

Flashing S G S7, or rather its Chinese copy. Alexey Zholdin 7 months A CHINESE device, created exactly where the device was assembled, as a rule, does not come out of anything good, or anything better, native firmware, on. Updating firmware is a great way to make important adjustments to the phone system, getting rid of it. Instructions for installing the official single-file firmware on S G S7 SMG930. Chinese Copy S G S7 Firmware M6571 Anton Chkalov. Smartphone I P 2 is an example of an excellent product from a little-known in Russia Chinese brand, on which

Firmware for Chinese S G S7 How to update S G S7? Now you can find out a lot about 7930 firmware Chinese 4, but there is only such a huge number of unique facts. In general, almost certainly the software on the copy of the G S7 will slow down and actively fail, but the update. For Chinese S G S7 M6572 Firmware. For Chinese S G S7 M6571 Firmware In general, the software on the copy of the G S7 will almost certainly slow down and. After clicking on the link, there is a 5 second advertisement, click. Firmware M6571 S S7 Chinese. I ask for help in finding firmware for a Chinese copy of S 7

Chinese 7 firmware. In general, almost certainly software on a copy of the G S7 will slow down and. EXACT Copy S G S7 ORDER 70% OFF LIMITED QUANTITY!

Today we will talk about how to flash Samsung Galaxy S7 and Galaxy S7 Edge. This guide covers the main issues related to the process of flashing a smartphone.

Important note: you will carry out all actions at your own peril and risk, the authors do not bear any responsibility for the possible consequences of operations with the device. If you are not sure, contact the experts.

Actually, there are three firmware options for Samsung Galaxy S7 and Galaxy S7 Edge:

1. "On the fly" - used only to install updates in automatic mode. Not suitable for unlocked carrier versions.
2. Across Samsung program Kies. This option is suitable for installing updates in cases where the on-the-fly installation fails for some reason, and for restoring the factory firmware.
3. With ODIN software. Used to install both original and modified and third-party firmware.

We will omit the first two options because of their simplicity and clarity. And we'll talk about something else.

How to flash Samsung Galaxy S7 using ODIN

PC Requirements: Windows XP SP3 or later. Your Samsung Galaxy S7 or Galaxy S7 Edge should be at least 30% charged, preferably 100%.

Stage number 1. Disable "Remote Management"

To successfully install a new firmware on a smartphone in the ODIN program, you need to disable the activation lock of the device. Otherwise, the firmware process will end with an error. In the new Samsung smartphones on Android based 6.0, this setting is called "Remote control".

Procedure:

a) Go to the section "Settings" -\u003e "Lock screen and protection".

b) Go to the "Find phone" subsection.

d) Disable the "Remote control" option.

See the original of this part of the manual.

Stage number 2. Install original Samsung drivers

At this stage, we install the original drivers for mobile devices Samsung based on Android OS. Download options:

1. Samsung Android USB Driver for Windows (drivers only) - link.
2. Samsung KIES(Software for synchronization with PC) - link.
3. Samsung SmartSwitch (Software for transferring data from one smartphone to another) - link.
4. SideSync (Software for common screen and data exchange with a PC) - link.

If you already have one of these installed, it will not be superfluous to check the relevance of the version.

Before installing the driver, connect your smartphone to the PC.

Stage number 3. Reboot

This stage is desirable for the correct installation of the driver.

Stage number 4. Checking the correct installation of the driver

Connect your smartphone with a USB cable to your PC and check for a new device in Device Manager. Also your Samsung Galaxy S7 should appear in My Computer.

If this does not happen, try replacing the cable with another (preferably original) or change USB port(if you have a desktop PC, try the ports directly on the motherboard).

Important: after checking the smartphone must be turned off!

Stage number 5. Download ODIN

Despite the fact that there are many sites on the network offering to download the ODIN software, we recommend that you do this only from trusted resources:

Stage number 6. Download firmware

Here we cannot say anything specific, it all depends on what firmware you want to install. The entire database of original firmware for Samsung smartphones is available on the Samsung Updates website.

It is advisable to unpack the firmware to the root of the disk. At least the path to the firmware file should not contain any other characters except Latin and numbers (no Cyrillic, spaces, etc.). Underscores are allowed.

Stage number 7. Launching ODIN

Unpack the archive with ODIN software and run the program.

Stage number 8. Activate bootloader mode

Turn off the Samsung Galaxy S7/Galaxy S7 Edge using the "Power" button. Further:

1. We press and simultaneously hold 3 buttons: "Home", "Volume down" and "Power".
2. We are waiting for the image to appear on the screen of the device.
3. Release all three buttons.
4. Press the "Volume Up" button once.

Stage number 9. We connect the smartphone

In this step, we connect the smartphone to the PC using a USB cable. Wait until the driver is installed and the smartphone is detected in the ODIN program. This will be signaled by the highlighted ID:COM field with the port number. In the example below - "-0:-" (the port number may differ in your case).

Stage number 10. Setting up ODIN

Open the "Options" tab in ODIN and check the boxes "Auto Reboot" and "F. reset time". By default, they are usually enabled, but it will not be superfluous to check this. The ODIN setup can generally be done before connecting the smartphone.

Stage number 11. Connect firmware files

We go back to the "Log" tab in ODIN and connect the firmware files in the exact order:

1. in the BL field -> file BL***tar.md5
2. in the AP field -> file AP***tar.md5
3. in the CP field -> file CP***tar.md5
4. in the CSC field -> file CSC***tar.md5 ( complete cleaning smartphone data to the out-of-the-box state) or HOME_CSC………tar.md5 (saving user data on the smartphone)

Stage number 12. Starting the firmware process

Press the "START" button and watch the process Galaxy firmware S7/Galaxy S7 Edge.

Instructions for flashing a Samsung Galaxy S7 SM-G930 smartphone to a new official or custom firmware. Getting Root superuser rights on Samsung Galaxy S7 SM-G930, installation of custom recovery TWRP recovery.

How to flash Samsung Galaxy S7 SM-G930 to the official firmware using the Odin flasher program? In order to install new firmware on a smartphone, you first need to download several files to your PC:

Then you need to download any firmware for Samsung Galaxy S7 SM-G930 that you like, for example:

Decoding of models:

Operator models:
SM-G930T (T-Mobile)
SM-G930A (AT&T)
SM-G930P (Sprint)
SM-G930V (Verizon)
SM-G930R4 (US Cellular)
Regional Models:
SM-G930I (Australia)
SM-G930F (Europe)
SM-G930G (International)
The prefix D in the model means two-symbol (Duos)

After you have downloaded everything, unpack the archive with the driver for Samsung Galaxy S7 SM-G930 and install it. Then unpack the archive with Odin and the firmware.
We launch the Galaxy S7 Odin firmware program as an administrator. To do this, hover over Odin and right click mouse and select "Run as administrator", then click "Yes".

After starting Odin, we arrange the firmware files in the following order:
File BL……….tar.md5 is inserted into the field "BL"
AP file……….tar.md5 is inserted into the field "AP"
The CP file……….tar.md5 is inserted into the field "CP"
CSC file……..tar.md5 is inserted into the field C.S.C.

We check that the “checkmarks” are only in the fields “Auto Reboot” and “F. Reset Time”

Translation samsung phone Galaxy S7 SM-G930 in firmware mode. To do this, turn off the phone and then press and hold the "Volume Down", "Home" and "Power" buttons and after the menu with a yellow triangle appears, press the "Volume Up" button
We connect the smartphone using the supplied USB cable to the PC and Odin program, in the upper left corner the inscription “COM” should appear highlighted with a blue background, after which we press the “Start” button.

Note: If for some reason your PC does not recognize your device, try reinstalling the driver and / or try other USB ports.

The smartphone firmware process has been started. After successful firmware, the device will reboot automatically and “Finish” will appear in the Odin program. That's all!

Instructions for installing custom recovery TWRP recovery on Samsung Galaxy S7 (SM-G930)

To install custom recovery TWRP Recovery on a Samsung Galaxy S7 SM-G930 smartphone, you first need to download the USB driver and install them - SAMSUNG USB Driver (if you have not already done so).
Download and unzip the flash driver - Odin
Download latest version TWRP for SM-G930F (herolte) from this TWRP SG S7 repository in .img (Image) / .img.tar format (for Odin)
In the smartphone settings, enable “USB Debugging” + OEM Unlocking in the “For Developers” settings section, which in turn opens if you click 7-10 times on the “Build Number” item in settings section “About phone”
Then turn off the smartphone and go to the “Download Mode” firmware mode, to do this, on the switched off phone, simultaneously hold down the “volume down”, “Home” and “Power” buttons.
Before you enter the firmware mode, the phone will display a “Warning”, press “Volume +” to skip.
Connect your Samsung Galaxy S7 SM-G930 phone to your computer using a standard USB cable.
Run Odin (previously downloaded and unpacked) and wait for the inscription “Added” (“Added” / “Connected”), and if the inscription does not appear, repeat the previous points.
After you see the message “Added” (“Added” / “Connected”), click on the “AP” button and find the previously downloaded TWRP files.
Check the "Auto-Reboot" checkbox
Go to TWRP and flash this file - no-verity-opt-encrypt (it is for normal TWRP operation)

Everything!! On your Samsung smartphone Galaxy S7 installed custom TWRP recovery recovery.

Installing custom firmware on Samsung Galaxy S7 SM-G930

To install custom firmware on a Samsung Galaxy S7 SM-G930 phone, you need to have TWRP Recovery custom recovery, if you don't have it, see the paragraph above.