Components

Detailed instructions for properly configuring a ZTE router. How the ZTE ZXHN H118N router is configured by Rostelecom A router of this type in its design has

ZTE ZXHN H108N is a modem that has spread widely among major operators in several countries, such as Ukraine, Kazakhstan, Russia. It is recommended, rented out. ZTE ZXHN H108N modem supports the technology ADSL connections, enables wired and wireless Internet access. The ZTE ZXV10 H108L modem is configured according to the same principle. Setting up the ZTE ZXHN H108N modem is not difficult, any user who has carefully studied the instructions below can do it.

Setting for work

For ZTE ZXHN H108N, the modem is adjusted through the browser after. Entering the settings interface is possible through any browser, where in the address bar enter 192.168.1.1, press Enter.

In the authorization window, type the same word in the User name, Password lines - admin. After clicking OK, a window with settings will open.

If your router has already been used before, clear its settings by resetting it to factory settings. This is done by pressing the Reset button located on the rear panel. Press it for 10 seconds, wait for the modem to reboot. After the system prompts you to change the password, enter the old username, the new password.

Enter the type of DSL connection below if requested.

The next steps are set in agreement with the provider, usually they can be found in the contract or clarified by phone.

The connection type is often set to PPPoE, if the provider has assigned a dynamic IP, DHCP is set.
Enter then VPI/VCI again, taking from the contract. Below you will see “Connection with LAN ports”, check the boxes where you planned to distribute the Internet, it is advisable to leave the last port free. Also check SSID1 for Wi-Fi to work.

Then you will be asked to connect WAN - for television, if the service is connected, agree and put the necessary data there.

When the reboot occurs, the device will be ready to function with the numbers entered.

WiFi setup

After the ZTE ZXV10 H108L is rebooted, the modem will be ready to work.

To configure any of the routers of the ZTE line, it is first recommended to prepare the authorization data for the Rostelecom Internet connection, since it will not work to activate the network without them. In most cases, the provider uses the PPPoE type of service connection. These parameters are used to establish communication using ADSL and Ethernet technology. There are also less common options for connecting services that can be used when running a fiber optic cable directly to the client's apartment or private house.

Configuring Rostelecom parameters for ZTE brand routers

ZTE is one of the largest companies in the global electronics market. In addition to the manufacturer’s smartphones, which have recently gained immense popularity, which have a lower cost than similar products from the LG and Samsung brands, but are not inferior to them in terms of characteristics and quality, the company also occupies a strong position in the field of network equipment.

ZTE provides its customers with a wide range of devices to create a home or corporate network. For users who need the Internet outside the city, where it is not possible to create a wired connection, the manufacturer offers ZTE modems MF 190, distributed both with native (factory firmware) and with an already built-in modification from Rostelecom.

These can connect directly to a computer or with the help of routers that support the appropriate connector and technology.

Attention! There is no possibility to reflash ZTE MF 190 modems from Rostelecom or other operators using official methods. For such tasks, the Dc-Unlocker program is usually used.

Also in the line of network equipment, ZTE also has routers, for example, H108N, adopted by users as an Ethernet modem for Rostelecom to set up high-speed home and work networks.

Preparing to set up the equipment

Before setting up ZTE routers under Rostelecom, for example, the E5501 model, you need to check the equipment package, which contains:

power supply (12V converter);
at least one Ethernet cable.

Of course, in the newly unpacked box from the device there will also be a software disk, a warranty and a lot of literature, but these components do not play an important role in setting up a ZTE modem under Rostelecom.

Attention! Even if you want to use the Internet only via Wi-Fi, an Ethernet cable is in any case an indispensable component that is needed for initial setup.

To connect the device, the first thing you need to familiarize yourself with is the ports on the rear panel.

Having deployed the ZTE E5501 side with functional connectors, as on the ZXV10 W300, here you can find:

four LAN ports;
Ethernet port;
connector for the power cable.

The ZTE H108N model will have one difference from the above modems, namely a connector for an ADSL cable ( telephone cable), since this router is designed for Internet over a telephone line. This will not significantly affect the overall sequence of connecting network equipment. First of all, we connect the power supply to the socket and the port on the router, and then we insert the Internet cable into the WAN or ADSL port (depending on the modem model, one of these ports will be present). Now we find the RJ45 connector on the computer (standard network input) and connect it using an Ethernet cable to the corresponding port on the router. Since in our case there are four connectors, you can connect the cord to any.

Attention! If the ZTE H108N is configured, then in addition to the described sequence, it is also recommended to connect a splitter that filters the Internet and network signals. This will allow you to use two provider services at the same time.

When all the cords are connected, it will be possible to turn on the equipment, which is done using the button on the rear panel.

Now let's move on to the front of the device. It contains indicators that will help you find out about the status of options when setting up ZTE ZXV10 W300, H108N or E5501 modems for Rostelecom. For example, here is information about:

in which of the connectors is the computer connected;
is Wi-Fi working;
whether there is a connection to the provider and the Internet.

Setting up an Internet connection on ZTE ZXV10 W300, ZTE H108N, ZTE E5501

When the connection part is completed, you can proceed to setting up modems for Rostelecom, which we will do using the ZTE ZXV10 W300 as an example. We go from a computer connected directly to the modem to the browser and write the router's IP address in the address bar. You can find it in the equipment passport. In our case, it will be 192.168.1.1. Now we enter the standard login and password, which are also indicated in the instructions for the modem (admin / admin).

After that, you will be redirected to the control panel software devices. In the Network tab, select the WAN parameters and make PPPoE setup connections according to the data provided by the provider. They can be found in the contract or on a special Rostelecom card.

Because the hardware supports wifi settings and such a modem is usually bought with the intention of connecting to the network wireless devices, you can configure the module operation on the Wireless tab. Here we select the network name (SSID), and also create a security key that will prevent unauthorized clients from connecting to your wireless network.

From ZTE, depending on its type (portable or stationary), it is produced in several stages. In the case of installing routers for private apartments or small offices, a suitable place is first selected, then the connection is made, and after that the connection parameters are entered.

Rostelecom

Any of us from time to time is faced with the need for a router option, using which we connect to the Web. Here, if you are the owner of a router from Rostelecom, your company will need the following information under any circumstances.

It remains for our client what is useful for you - a router, a laptop or a computer with Wi-Fi function and a little extra time. First of all, you need to open a successful Internet browser for you and in the search bar enter the address of the router, which you will find on a sticker on either top panel devices.

It consists of numbers and dots: for example,

192.168.1.1

When entering the correct number, wait for the authorization window, where you will be asked to enter your personal data as a Rostelecom subscriber. After that, wait for the necessary settings to appear.

Tune

router

via Wi-Fi module

If your router does not have a connection to the computer via a patch cord, then you need to spend time on the ability of the equipment to work with the Wi-Fi function. Just turn on the router and go to the "Network Control Center" to make sure the wireless Internet connection is active.

Read also

How to determine under which operator the iPhone is locked by IMEIWhile buying an iPhone abroad, for its subsequent opening activity, it is extremely important to find out under which operator it is locked in order to assess how difficult the process will be ...

How to remove the screen lock on a Samsung phone? Screen lock is a reliable method android protection devices from third parties. Many Samsung phones this tool is pre-installed, so anyone can use it. If numbers...

The popularity of tablets in Russia is growing not from year to year, but almost day by day. There are more and more new devices in both the premium and economy sectors, with the latter not far behind the performance of expensive models. Use pl...

How to disable the screen lock on AndroidThe lock screen is a great way to protect android smartphone from outsiders accidental clicks which is to provoke the leakage of personal information in another way unwanted calls. However, with blocks...

Disassembly Lenovo laptop Ideapad B590. Cleaning the laptop from dust and replacing the thermal paste. Main page » Disassembling the Lenovo Ideapad B590 laptop. Cleaning the laptop from dust and replacing the thermal paste. Disassembling the Lenovo Ideapad B590 laptop. Cleaning laptop...

It's almost 2020 and android phones ALWAYS unable to record more than 4GB of 4K 60fps motion footage. The camera app doesn't stop recording completely despite this. It's just that your entry will be split into...

To activate the connection, you must set up Wi-Fi and enter a password for it. When setting up the modem for the first time, the password has not yet been invented, and you can create it in the router settings menu. Wrong password It could happen that

router

Setting up a ZTE modem

ZXHN H208N

Setup of the ZTE ZXHN

H208N modem

Modem setup ZTE ZXHN H208N router, WiFi setup, IPTV Setup of the ZTE ZXHN H208N modem in a router, the.

Setting up a wi-fi router zte zxhn h108n, internet, wi-fi, interactive TV, multiroom

Detailed description of DSL wi-fi ZTE router zxhn h108n, manual and master setup Internet, interactive TV, wi-fi.

In this case, you should reset the current settings to the factory settings: to do this, press the configuration reset button deeply hidden in the router. Hold the button for a couple of seconds until all buttons on the router are lit.

Read also

HTC Sync and HTC Sync Manager HTC Sync Manager keeps your HTC devices in sync with your computers. Supported by our client remains the latest HTC smartphones One, Desire, Butterfly series and more.HTC Sync Manager provides sync...

Why Odnoklassniki is not openingHere are a few reasons why Odnoklassniki and Contacts are not enabled, and what to do if you see on your page in in social networks that your Account blocked or something like that.Suddenly you are completely...

Changing the matrix, screen, LCD (LED, 3D) LG TV No need to be surprised if your LCD (LED, 3D) LG TV failed, our client is left with what exists, that our client is left with LCD TVs very sensitive to any, even the most the smallest mechanic...

Often, iPhone users come up with the question of how to put a melody on iPhone call. After all, everyone wants to install such a ringtone on an iPhone so that it amuses the ear. Setting the music for the call is not particularly difficult if ...

To you, P20 Pro Huawei almost a year though This phone still remains one of best phones in manufacturing.Pro arrives, flaunting a 6.1-inch AMOLED display, smart triple rear camera and a fast Kirin processor. Although...

Cash. quite an old instrument. He became a part operating system in the earliest Windows versions. Cache. it is a system repository that allows you to store the information needed to random access memory. This tool allows...

Now wait full reboot device. You can then enter your username and password below. If everything went right, the browser window should display

settings menu

devices. In the event that this did not help, you should think about the malfunction of the router. The first step is to seek help from qualified professionals.

Classification of settings

settings menu

device, you have the ability to change the parameters of the router at your discretion. They are of the following types:

Settings for creating and changing a password and name;
Setting a password for Wi-Fi;
Configuration of the router with the Rostelecom server;
Regulation of the connected equipment;
Blocking the ability to connect inappropriate devices;
Change of equipment hierarchy

When you can’t enter the settings of your router on your own, you should turn to more experienced Rostelecom specialists for help. To do this, you can use the contact number of the operator or the form feedback on the official website of the company.

Post Views: 10

The router from the manufacturer ZTE is a model that can only work on FTTB lines. Setting up the ZTE ZXHN H118N Rostelecom router can be done both using the wizard built into its program, and in manual mode. IPTV and SIP telephony are supported.

Login can only be done after connecting the ISP cable to the WAN port (RJ-45) on the back panel of the ZTE ZXHN H118N Rostelecom router. One of the 4 ports of the LAN router (RJ-45) is connected by an Ethernet line with a connector network card computer (PC) or laptop used for setup. You must first set the automatic mode for obtaining addresses by the device on the Internet Protocol version 4 page.

According to the information on the sticker, it can be seen that the IP address of the device is 192.168.0.1 - and its authorization data is used by default: username - admin, password - admin. The network address is entered in address bar the web browser used on the PC, and information about the login and password is required to fill in the fields of the window that opens.

The router program requires the provider cable to be connected to the WAN connector, and the first login page will remind you of this in case of violation necessary condition. If the router detects an Internet connection, then the page looks different. Suggestions appear on it about choosing a time zone and the need to change the factory password with the corresponding information fields.

After fulfilling the security requirements, you must click on the "Continue" stencil and go to the next page. On it, you need to select the proposed configuration method: "Start the wizard", "Configure the device manually".

How to make the menu complete

Rostelecom router is configured after selection manual setting. To enter the menu, you need to enter the data of the username - admin - and the created individual password. Clicking on the Login tab will take you to start page router interface with general information about the device. The item "Network" in its left part opens the possibility of choosing the type of WAN connection.

When configuring, the data provided by the provider when concluding an agreement with him is used: type of Internet connection (PPPoE), number of the included VLAN (optical fiber) and its priority, username and password. Connection to be created should be "Always On". The entered data is saved when you execute the "Edit" command at the bottom of the page.

To use the TV function, you need to re-open the list of possible WAN connections and select IPTV from it. In the connection type line, use "Bridge" and then execute the "Create" command. The field of this is necessary in the WAN section of the main menu, go to the "Port Binding" item.

It produces program purpose connectors LAN1-LAN4. For PPPoE, LAN1-LAN3 ports are selected by default. Computers will be connected to them. For IPTV, you need to assign LAN4. A set-top box will be included with it, which will use it over an Ethernet cable line. After setting the checkboxes in the selected cells, click the "Save settings and confirm" button.

Setting up Wi-Fi on an Ethernet router ZTE H118N

Router manufacturer ZTE provides its products with customized wireless connection WiFi. Information about the network name and access password can be found on the label on the router case. But the connection setup can be done manually. To do this, in the VLAN section ( Wireless network) the menu should select the item "Setting Wi-Fi networks".

On its page, you can change the factory settings to your own. After selecting the "Security" item, it becomes possible to change the authentication type and encryption algorithm. Finally, click the Save button ("Apply").

Popular settings

Apply automatic tuning router Rostelecom after the proposed change of the factory password. If after that you click on the "Start Wizard" stencil, then in the next step you need to select and specify the region, branch and service of Rostelecom. After continuing the settings, you must fill in the login and password fields issued by the provider when concluding the contract. If the branch uses "Dynamic IP", this data will not be needed.

When connecting a set-top box, it must be assigned a LAN4 port. After continuing, the wizard will prompt you to change the authorization data. You can do this and continue. The next page prompts you to enter the settings with the new Wi-Fi network values, administrator name and password, click the "Save settings" button.