A computer

Installing a zte corporation router. Detailed instructions for properly setting up a ZTE router

4G/ wifi router ZTE MF90 is quite extraordinary for 2015-2016 (it was then that the modem first appeared on the "mass" market), but at the same time, a high-quality device that meets the basic requirements for the functionality and mobility of the router.

It should be noted right away that the device is "locked" to work with the Beeline operator, and is sold mainly through the sales offices of this provider.

Router zte mf90 specifications: overview and specifications

For a fairly reasonable price (around three thousand rubles), Chinese developers have provided a quality mobile router with competitive features.

1. Baud rate:

- with "LTE FDD" up to 100 Mbps - when receiving, and up to 50 Mbps - when transmitting;
- with "DC-HSPA +" up to 42 Mbps - reception, and up to 5.76 Mbps - transmission;
- with "EDGE/GPRS" up to 236 Kbps.

2. Support micro SD memory cards up to 32GB.

3. Li-ion battery at 2300 mAh.

These characteristics fully provide comfortable surfing on the net: the battery allows you to freely use all the benefits of the Internet for 6-8 hours.

Zte mf90 router: indicators and connectors

Due to its mobility, the router had to “sacrifice” the indicator part.

There are only three indicators on the front of the device:

- "Battery charge". When the indicator “burns” or “flashes” red, you need to charge the battery. If the light “blinks” green, the battery is being charged (the charge level is not lower than average or the battery is fully charged).
- “Network signal strength”. The indicator constantly "burns" red - there is no signal, or "USIM" is not installed. "Lights" green - registration in the 2G / 3G network, "blinks" green - the router is connected to the network and data is being transferred, if the indicator is "lit" in blue, this means that the device is connected to the 4G network.
- WiFi network. If the indicator is “blinking” blue, the wireless network is enabled, if it is “lit”, then WPS is enabled.

Below the display panel are the "Power" (Power On / Off) and "WPS" buttons, also designed to turn on or off wireless network(when pressed once), but if you hold the button for 5 seconds, the WPS mode will turn on.

On the side there are two connectors for connecting 2 additional antennas and a connector for "mini-USB" - for synchronization with a computer or connecting a charger.

There are two slots inside the case for the battery: one for "USIM", the second one for "microSD". And on the opposite - relative to the side buttons - side of the router there is a recess with the "Reset" button (i.e. reset to factory settings).

How to connect the zte mf90 modem by yourself?

The procedure for connecting the zte mf90 router is as follows:

Open the lid and insert into the corresponding USIM slot of the Beeline operator.

- Look for a sticker inside the case that lists the "SSID" of the wireless network (specified in the format MF90_XXXXXX, where x is a unique number assigned to each device) and password. Remember them - in the future, these data will be useful to you.
- Install the battery and close the cover.
- Use the "Power" button to turn on the device (the corresponding indicators will light up) and connect the router and the computer with a "USB cable".

- Search for available wireless networks (based on the “SSID” obtained above) and connect to the network by entering the password.
- Next to address bar browser, enter 129.168.0.1 or m.home (the default password is "admin").

To change the password to enter the settings of the zte mf90 router, use the "Management" section. Here you can also configure the power saving mode, pin-code "USIM" and settings for sending "SMS messages".

How to set up an internet connection on a zte mf90 router?

Internet access is configured through the router interface.

The first step is to carry out the "Activation of the starting balance":

Open the "Service Management" section;

In the drop-down menu, select "Activation of the starting balance";

Click the "Activate" button.

If payment will be made using Beeline payment cards, in the "Service Management" section, select "Payment card activation" and enter digital code cards (without using spaces or hyphens).

You can also use the "Request funds from another subscriber" service: in the same section, select "Ask for money from another subscriber", enter his phone number without the eight and click "Send". Just waiting for payment. But you should not abuse this service, as there is a restriction - you can send a request no more than 5 times a day.

To complete the settings, you only need to click on the "Connect" button and select one of the connection modes:

- if you select "Automatic", then when you turn on the device will independently conduct an Internet connection;
- if you set it to "Manual", you will need to visit the web interface every time you turn on the device to access the Internet.

How to set up wifi on a zte mf90 router?

To set up a wireless network, go to the "WiFi" section and do the following:

- enter the name of the network in the line "Network name (SSID)";
- check the box "Enable" in the line "Transmission of the network name (SSID)";
- "Network encryption type" leave "WPA-PSK" - "WPA2-PSK";
- in the "Password" field, enter the security key to connect to created network;
- in the line "Maximum connections" set maximum amount devices to be used this network(but not more than 10).

In the "Firewall" section, filtering and port forwarding are configured, as well as enabling and disabling "UpnP / DMZ".

The “Router” section allows you to change the “ip address” of the router, get acquainted with its “mac address” and configure the “DHCP server”.

In chapter " WiFi Internet" you can set up and use "mf90" as a repeater.

Thus, the ZTE MF90 4G / WiFi router is an excellent mobile option for a relatively low price, which opens up extensive opportunities for web surfing in transport, at work or in any other places where the use of standard routers is unacceptable.

Beeline zte mf90 router unlock

Unlocking (unlocking) the ZTE MF90 router, yes, in principle, and all other routers tied to the same provider, is not a difficult matter, but it requires attention (and an elementary understanding of where everything is in the computer).

1. First, download and extract the firmware that allows you to unlock zte mf90. It will not be difficult to find it: with any request like “How to unlock the MF90 router”, many options will appear where you can download this very archive.

4. Now you need to put the router into diagnostic mode. Go to "http://m.home/goform/goform_process?goformId=MODE_SWITCH&switchCmd=FACTORY".
Please note that the diagnostic mode is a temporary parameter, so do not hesitate and immediately proceed to the next step.

5. New equipment with the name "ZTE Mobile Broadband DiagnosticsPort" will appear in the "Device Manager" - open the "Ports" section and remember which port is assigned to COM4 or COM13.

6. Place the file with the permission ".bin" from the downloaded archive into the root of the "C:" drive.

8. Disconnect and reboot the router.

In conclusion, you can check with any convenient utility for checking the binding whether your router is unlocked or not.

The router from the manufacturer ZTE is a model that can only work on FTTB lines. Setting up the ZTE ZXHN H118N Rostelecom router can be done both using the wizard built into its program, and in manual mode. IPTV and SIP telephony are supported.

Login can only be done after connecting the ISP cable to the WAN port (RJ-45) on the back panel of the ZTE ZXHN H118N Rostelecom router. One of the 4 ports of the LAN router (RJ-45) is connected by an Ethernet line to the network card connector of the computer (PC) or laptop used for configuration. You must first set the automatic mode for obtaining addresses by the device on the Internet Protocol version 4 page.

According to the information on the sticker, it can be seen that the IP address of the device is 192.168.0.1 - and its authorization data is used by default: username - admin, password - admin. The network address is entered into the address bar of the web browser used on the PC, and information about the login and password is required to fill in the fields of the window that opens.

The router program requires the provider cable to be connected to the WAN connector, and the first login page will remind you of this in case of violation necessary condition. If the router detects an Internet connection, then the page looks different. Suggestions appear on it about choosing a time zone and the need to change the factory password with the corresponding information fields.

After fulfilling the security requirements, you must click on the "Continue" stencil and go to the next page. On it, you need to select the proposed configuration method: "Start the wizard", "Configure the device manually".

How to make the menu complete

Rostelecom router is configured after selection manual setting. To enter the menu, you need to enter the data of the username - admin - and the created individual password. Clicking on the Login tab will take you to start page router interface with general information about the device. The item "Network" in its left part opens the possibility of choosing the type of WAN connection.

When configuring, the data provided by the provider when concluding an agreement with him is used: type of Internet connection (PPPoE), number of the included VLAN (optical fiber) and its priority, username and password. Connection to be created should be "Always On". The entered data is saved when you execute the "Edit" command at the bottom of the page.

To use the TV function, you need to re-open the list of possible WAN connections and select IPTV from it. In the connection type line, use "Bridge" and then execute the "Create" command. The field of this is necessary in the WAN section of the main menu, go to the "Port Binding" item.

It produces program purpose connectors LAN1-LAN4. For PPPoE, LAN1-LAN3 ports are selected by default. Computers will be connected to them. For IPTV, you need to assign LAN4. A set-top box will be included with it, which will use it over an Ethernet cable line. After setting the checkboxes in the selected cells, click the "Save settings and confirm" button.

Setting up Wi-Fi on an Ethernet router ZTE H118N

Router manufacturer ZTE provides its products with customized wireless connection WiFi. Information about the network name and access password can be found on the label on the router case. But the connection setup can be done manually. To do this, in the VLAN (Wireless network) section of the menu, select the item "Configuring Wi-Fi networks".

On its page, you can change the factory settings to your own. After selecting the "Security" item, it becomes possible to change the authentication type and encryption algorithm. Finally, click the Save button ("Apply").

Popular Settings

Apply automatic tuning router Rostelecom after the proposed change of the factory password. If after that you click on the "Start Wizard" stencil, then in the next step you need to select and specify the region, branch and service of Rostelecom. After continuing the settings, you must fill in the login and password fields issued by the provider when concluding the contract. If the branch uses "Dynamic IP", this data will not be needed.

When connecting a set-top box, it must be assigned a LAN4 port. After continuing, the wizard will prompt you to change the authorization data. You can do this and continue. The next page prompts you to enter the settings with the new Wi-Fi network values, administrator name and password, click the "Save settings" button.

The router is network hardware, allowing many devices to access the Internet at the same time (computers, tablets, smartphones and much more). Today's range of routers allows you to choose exactly what is most suitable in a particular case.

Overview of routers

There are several models that are optimal for home use:

ZTE E5501;
Zte H118N;
ZTE E5502;
Zte ZXA10 f660.

ZTE E5501

This device supports multiple interfaces:

4 ports for an RJ-45 connector (which allows you to work with data through a network interface, the cable type is detected automatically);
works according to the 802.11n communication standard (frequency 2.4 GHz);
There are two non-removable antennas that ensure stable Wi-Fi operation.

In addition to supported interfaces this device It has many other options that make it quite convenient and easy to use.

Zte H118N

A router of this type in its design has:

USBv.2 in the amount of 1 piece for connecting a 3G modem (optional);
4 ports for connecting a cable crimped with an RJ-45 connector;
WiFi (IEEE 802.11n).

The maximum data transfer rate of this device is 300 Mbps. It also supports several data encryption technologies - WEP, WPA, WPA2.

Zte 5502

The considered router from such an eminent company is in no way inferior to its classmates:

4 ports for cable connection via RG-45 connector;
supported: IEEE 802.11n ( maximum speed transmission - 300 Mbps);
there are two antennas for operation in the 2.4 GHz band;

The encryption capabilities of the device in question are the widest:

WEP with 64/128 bit encryption technology;
WPA-PSK;
WPA2-Interprise and many others.

ZteZXA 10 F660

The ZTE router has not only excellent performance, but also a relatively low price.

It is easy to set up and also supports all the necessary technologies:

there are 4 connectors for RG-45;
2 connectors for working with POTS interface (RG-11);
successfully works with Wi-Fi technology;
There is a connector for connecting USB devices.

Choose a device

When choosing a router for your home, you need to consider the following important points:

ease of setup - so that in case of any problems you can fix them without calling a specialist;
price - this question especially relevant for families with many children;
reliability;
features of the Wi-Fi module.

The simpler the design of the device, the easier it is to configure. That is why you should give your preference to those routers that do not require dancing with tambourines during connection and start work. This will save a large number of time.

Video: How to open a port on a ZTE ZXA10 F660 router

Price range is very important point . Today it makes no sense to purchase expensive devices. Since even the youngest models in the line have everything on board that is required for comfortable work with a Wi-Fi network at home. You should not overpay for a model brand - usually such expenses are completely unjustified.

Choosing the best option for the price, you should not buy very cheap models. Since often behind the extremely low price there is not the highest workmanship, which may soon lead to a breakdown.

The Wi-Fi module must necessarily have an antenna located outside the case. Since antennas of this type have a large area. Which is very important if the apartment or house has a large footage. Also, the antenna should be removed and replaced if necessary - as an extension of the coverage area may be necessary.

The best choice in all respects is the ZTE ZXA10 F660 router. It has many advantages, as well as a fairly low price (considering the rather good parameters).

PC connection

The easiest part of setting up a ZTE router is connecting it to a PC. This operation is performed in the following order:

Settings management

How to set up a router ZTE WiFi? The settings are managed using the WEB-interface, which can be accessed through any browser installed on the PC. For example, internet explorer. In the address bar, enter the following combination of numbers and symbols - http://192.168.1.1. If the router is connected to the computer according to the instructions, a window will appear in which you can enter your login and password.

By default, the password and login is the word admin (only in Latin letters). When the fields are filled, you should click the "Login" button. Next, a window will appear, made in green and white colors.

The top has the following tabs:

status;
network;
security;
application;
administration.

Each tab allows you to manage a particular section.

For wifi settings you should do the following:

This list of actions enabled Wi-Fi.

Special attention should be paid to the section called "Multi-SSID".

Optionally, this section allows you to make the network both open and closed for various types of devices:

SSIDName - this item allows you to name the configured network by any name;
MaximumClients - the maximum possible number of simultaneously connected devices ( this model supports 32pcs);
EnableSSID - enable or disable the network being changed;
HideSSID - hiding the wireless network;
ChooseSSID - select a Wi-Fi network to change.

A photo: wifi setup on the Promsvyaz modem

There is also a Security section in which you can configure the following items:

When choosing a password, it is advisable to follow the following recommendations:

the presence of lowercase and uppercase letters (in random order);
password length must be at least 10 characters;
the presence of numbers is also desirable.

Setting up a ZTE router for providers

The ZTE ZXA10 F660 router is configured differently, depending on which provider is the Internet service provider (MGTS, Rostelecom, Ukrtelecom).

Ukrtelecom

Setting up work with this operator requires special care, since all the nuances should be taken into account:

In the “Multi-SSIDSettings” and “Security” sections, all settings are set according to the instructions that came with the device.

Particular attention should be paid to the "AccessControlList" section. The "Mode" item must be set to "Block". "MACAddress" - 00:13:e0:81:97:ee.

Rostelecom

Setting up a router to work with the Rostelecom provider is not difficult.

You need to do the following:

When the above steps are completed, you should configure the "Multi-SSIDSettings" section:

in the "ChooseSSID" item, set the value of the SSID;
check the box next to "EnableSSID";
"SSIDName" allows you to select a network name.

After completing all the settings, you must click the "Submit" button.

MGTS

To correctly configure the considered model of the router with the MGTS rights provider, you must perform the following steps in strict order:

This will enable Wi-Fi. The remaining settings are performed in accordance with the manual that came with the router.

It is also mandatory to configure a section called Multi-SSID. This section allows you to set a personal identifier for the network, as well as optionally hide it. All settings are performed individually, depending on the personal preferences of the user.

The section called "Security" allows you to configure the encryption settings and password for connecting to the network.

The ZTEZxa10 F660 router is the best device in terms of price-quality ratio. An excellent choice for home and office. This network equipment is easy to configure, compact, reliable.

Router released last season zte zxhn h108n has found wide application in the networks of the largest telecom operators. The Ukrtelecom provider is no exception, which recommends purchasing this device to connect to its network and rents it out.

The modem supports Internet connection using ADSL technology. It can provide access to global network four subscribers through wired interface, as well as the device is equipped with a WiFi module for creating wireless connections.

The presented instructions will show how to set up a zxhn h108n or a similar zxv10 h108l device to work with the Ukrtelecom provider. It should be noted that the algorithm WiFi connections router to other telecom operators is not much different, so the instructions will be useful to users of other networks.

To connect a WiFi router to the Ukrtelecom network using ADSL technology, perform the following operations:

Connect the power supply to the Wi-Fi modem through the "Power" connector, then plug it into the electrical network.

Connect the “Line” port of the splitter included with the WiFi router to telephone socket. Connect zxhn h108n or zxv10 h108l to the “Modem” port, on which the required socket is labeled “DSL”. In the “Phone” port, connect the telephone set, if any, and conclude an agreement with Ukrtelecom for the provision of this type of communication.

To configure the parameters of the zte zxhn h108n or zxv10 h108l, connect your computer to it via an Ethernet cable (included). For this, the “LAN1” port on the Wi-Fi modem is used, and on the PC, the network card connector.

Computer settings

In cases where the computer is connected, and the corresponding LAN indicator on the front panel of the WiFi router is not lit, you should configure network card PC.

Windows 7

Through the "Start" activate the "Control Panel" and click on "View network status and tasks."

Click on "Change adapter settings".

Right-click on the active connection. A list will appear where you should select the "Properties" value.

Double click on "Internet Protocol Version 4(TCP/IPv4)".

Switch the dialog boxes to the states shown in the following figure.

Commit the changes by clicking on "OK" in all open windows.

In Windows 8 (eight), the setup is performed in the same way, but in order to open the "Control Panel" you need to right-click on the "Start" menu and select "All Applications", where the necessary link will be.

Internet connections

Setting up zte zxhn h108n or zxv10 h108l for Ukrtelecom is better from the factory settings, so the parameters of the used modem should be reset. To do this, press and hold the “Reset” button recessed in the device case for at least ten seconds, and then wait for it to reboot.

The modem connected to the network using ADSL technology and to the computer with an Ethernet cable is configured according to the following algorithm:

Log in to the device web interface using an Internet browser, to do this, type the link 192.168.1.1 and launch the transition through it.

Open a browser, enter http://192.168.1.1 in the address bar

In the main window of the Wi-Fi router interface, find the link to the "Interface Setup" tab and click on it, and then on the "Internet" settings item.

DHCP

To configure a DHCP connection, change the values of the fields:

PPPoE

For settings PPPoE connections changing fields:

After completing the configuration of the necessary connection, save the changes by clicking on "Save".

For the change to take effect, restart the WiFi router by going to the "SysRestart" item of the "MainInterface" tab. Here, select the "Current Setting" item and click on the "Restart" button.

Wait for the zte zxhn h108n or zxv10 h108l to finish rebooting and access the Internet from your computer using ADSL technology.

WiFi setup

To enable the grant function wireless access on the Internet via WiFi, you must perform a number of additional steps:

In the web interface of the Wi-Fi router, go to the "Interface Setup" tab, where open the "Wireless" item.

Set up the following page fields:

"Access Point": Activated;
"Wireless Mode": 802.1 1b+g+n;
"Chanel Bandwidth": 20/40 MHz;
"SSID": The name of your network displayed in the list available connections on subscriber devices. It is chosen arbitrarily, but only numbers and Latin letters are allowed;
"Authentication Type": WPA2-PSK;
"Encryption": TKIP/AES;
"Pre-Shared Key": arbitrary network password, numbers and Latin letters are allowed.