Games

Zte wi-fi equipment and connection. Detailed instructions for properly setting up a ZTE router

The router from the manufacturer ZTE is a model that can only work on FTTB lines. Setting up the ZTE ZXHN H118N Rostelecom router can be done both using the wizard built into its program, and in manual mode. IPTV and SIP telephony are supported.

Login can only be done after connecting the ISP cable to the WAN port (RJ-45) on the back panel of the ZTE ZXHN H118N Rostelecom router. One of the 4 ports of the LAN router (RJ-45) is connected by an Ethernet line with a connector network card computer (PC) or laptop used for setup. You must first set the automatic mode for obtaining addresses by the device on the Internet Protocol version 4 page.

According to the information on the sticker, it can be seen that the IP address of the device is 192.168.0.1 - and its authorization data is used by default: username - admin, password - admin. The network address is entered into the address bar of the web browser used on the PC, and information about the login and password is required to fill in the fields of the window that opens.

The router program requires the provider cable to be connected to the WAN connector, and the first login page will remind you of this in case of violation necessary condition. If the router detects an Internet connection, then the page looks different. Suggestions appear on it about choosing a time zone and the need to change the factory password with the corresponding information fields.

After fulfilling the security requirements, you must click on the "Continue" stencil and go to the next page. On it, you need to select the proposed configuration method: "Start the wizard", "Configure the device manually".

How to make the menu complete

Rostelecom router is configured after selection manual setting. To enter the menu, you need to enter the data of the username - admin - and the created individual password. When you click on the "Login" tab, you go to the start page of the router's interface with general information about the device. The item "Network" in its left part opens the possibility of choosing the type of WAN connection.

When configuring, the data provided by the provider when concluding an agreement with him is used: type of Internet connection (PPPoE), number of the included VLAN (optical fiber) and its priority, username and password. The connection you create must be "Always On". The entered data is saved when you execute the "Edit" command at the bottom of the page.

To use the TV function, you need to re-open the list of possible WAN connections and select IPTV from it. In the connection type line, use "Bridge" and then execute the "Create" command. The field of this is necessary in the WAN section of the main menu, go to the "Port Binding" item.

It produces program purpose connectors LAN1-LAN4. For PPPoE, LAN1-LAN3 ports are selected by default. Computers will be connected to them. For IPTV, you need to assign LAN4. A set-top box will be included with it, which will use it over an Ethernet cable line. After setting the checkboxes in the selected cells, click the "Save settings and confirm" button.

Setting up Wi-Fi on an Ethernet router ZTE H118N

Router manufacturer ZTE provides its products with configured wireless WiFi connection. Information about the network name and access password can be found on the label on the router case. But the connection setup can be done manually. To do this, in the VLAN (Wireless network) section of the menu, select the item "Configuring Wi-Fi networks".

On its page, you can change the factory settings to your own. After selecting the "Security" item, it becomes possible to change the authentication type and encryption algorithm. Finally, click the Save button ("Apply").

Popular settings

Apply automatic tuning router Rostelecom after the proposed change of the factory password. If after that you click on the "Start Wizard" stencil, then in the next step you need to select and specify the region, branch and service of Rostelecom. After continuing the settings, you must fill in the login and password fields issued by the provider when concluding the contract. If the branch uses "Dynamic IP", this data will not be needed.

When connecting a set-top box, it must be assigned a LAN4 port. After continuing, the wizard will prompt you to change the authorization data. You can do this and continue. The next page prompts you to enter the settings with the new Wi-Fi network values, administrator name and password, click the "Save settings" button.

Setting up a ZTE router is one of the main steps in connecting to a network.

Moreover, no matter what connection is used to access the network - - it will take a little time.

It does not affect the settings and models of routers - only the speed of access to and the way it is distributed to computers and other equipment depends on this characteristic.

Router selection

ZTE is one of the largest manufacturers of electronics, including routers.

And, although today the most popular are wireless routers that receive Internet via wireless 3G and 4G channels, one of the best options universal models can become for purchase.

That is, such devices that can receive and transmit data both using a cable and in other ways (mobile communications,).

The ZTE brand provides potential customers of its equipment with a wide range of different models that differ in functionality, speed of network access and data transfer.

Everything modern devices, even from the lowest price categories, provide wireless communication (), and many even connect to the network in the same way.

Thus, even relatively cheap models meet the requirements of most users.

Although, as a rule, the higher the price of the router, the more features it provides - including a wide range and a clear signal.

One of the most important characteristics is the number of antennas - the more there are, the greater the gain.

An even more convenient option is a router with the ability to connect additional amplifiers.

It is this technique that should be chosen for a large apartment and, moreover, for a private house, the territory of an entertainment center, a cafe or an office.

ZTE E5501

A popular router, released back in 2014, but still popular and sold online at a price of about 1000 rubles, is the ZTE E5501.

The advantage of the model is an attractive design (not so important, but still taken into account when buying a characteristic), support for 802.11n wireless technology and the presence of two antennas that amplify the signal by 10 dBi.

And a small drawback is the inability to connect a 3G modem and use other methods of connecting to mobile communications.

Rice. 1. A little outdated, but still quite functional and stylish ZTE E5501 router.

ZTE ZXHN H118N

Newer ZTE model ZXHN H118N with a price of about 1000–1200 rubles. already has a modem that allows you to connect to the network using mobile technology.

At the same time, there is also a WAN connector for wired access.

And the data is transmitted to other devices located within the range of the router, both via cable (4 LAN ports) and via Wi-Fi.

Rice. 2. ZTE ZXHN H118N - for wireless and wired network access.

ZTE 5502

Another model, in terms of functionality and price (about 900 rubles), reminiscent of the E5501 router, also looks quite stylish.

However, it has practically no advantages over other devices - only wired access is possible, and the network is distributed only in one range (at a speed of about 300 Mbps).

Although the ZTE 5502 encrypts information quite reliably (using WPA-PSK, WPA2, etc. technologies).

Fig.3. Bright and functional router ZTE 5502.

ZTE MF283

The MF283 model is capable of receiving (connection via SIM card), and with two wired connections at once.

In addition, you can connect a USB drive to the router to download information from the network directly without a computer, and telephone cable.

And, then, such a router will be great option both for the big house, and for office.

Moreover, the antennas of the device are removable, and can be replaced by more powerful elements.

Rice. 4. Model MF283 - a router with replaceable antennas and connection to a mobile network.

ZTE MF28D

The router works great both with wired connections (broadband and telephone) and with a mobile network.

It is worth noting that wireless connection is provided not with the help of 3G / 4G modems, like most routers of this type, but due to the SIM card installed in it.

And up to 2 antennas can be connected to the device, each of which amplifies the signal by 3 dBi.

Rice. 5. Router MF28D - for working with 3G / 4G Internet and wired connection.

Preparing for setup

Before connecting a router of any selected type, you should first check its contents. The router should come with:

power unit;
Ethernet cable for connecting to a wired network (except for options for connecting to the Internet using only mobile technologies);
instructions, warranty and CD software.

Important: When connecting two networks from different providers to the router at once (for example, via WAN and mobile communications), it is also advisable to install a splitter to filter the signal. And you can increase the coverage with the help of additional antennas.

Rice. 6. Connecting the cable to the network card of the laptop.

After connecting all the cables, you can turn on the router using the button located on the back.

The next step is to check the connection using the indicators on the front panel of the ZTE router. Here you can see signals showing:

to which connector the PC (laptop) is connected;
Is the wireless connection working?
whether there is a network connection.

If the device is connected to the Internet and a computer, and wireless connection valid, you can continue to configure the router.

For this, a web interface is used, which is present in any.

And after setting up the device, you can use it without a computer - just turn it on to connect with any gadget, including tablets and smartphones.

Creating an Internet connection

Management of ZTE routers for wired and wireless connection is carried out using a special interface, to which you can connect by specifying an address like 192.168.1.1 in the browser (you can specify this value in the data sheet of the router).

If the device is already connected to the PC, after entering these numbers, a settings window appears on the screen where you need to:

Enter username and password. By default, instead of each of them, the word admin is entered (if desired, they can be replaced by any others);
After filling in the fields, click on Login;
In the window that opens, select the Network section;
Open the WLAN tab in turn (sometimes you can select it immediately from the list, without going to the Network tab), and then Basic;
Select the WirelessRFMode column;
Change status from Disabled to Enabled ;
Press the button Submit, ensuring the inclusion of wireless data distribution.

Important: Most often, when connecting with a cable, the network is detected automatically. If this does not happen, you may need to update or install network card drivers. And then set up a new connection.

Now that it is enabled, you can configure the connection itself.

In the WAN Connection menu, PVC0 is selected in the Connection Name line, and Route is set in the Type line.

After that, you need to choose to enter the name and password of the connection (when connecting the PPPoE type), with which you will enter the network.

The ADSL network is configured in much the same way, although the transition is to a different tab.

Rice. 7. The process of connecting the router.

If the connection is made using a 3G / 4G connection, the setting is carried out through another tab - 3G WAN Connection.

Here, only the APN access point name is selected (you can find it on the provider's website or check with the company's technical support).

The rest of the settings are usually set automatically.

You should know: Depending on the model of the router, the names of the tabs may differ. For example, the access point name is sometimes required to be entered on a separate APN Settings tab. At the same time, all user actions will be approximately the same.

Additional sections

In addition to setting up a network connection, the user of the ZTE router has the ability to change other parameters:

for example, in the Multi-SSID section, you can make the network both open and closed;
the name of the connection is changed in the SSIDName column;
the maximum number of simultaneously connected devices is set in the MaximumClients item (most models support up to 32 connections simultaneously);
in the EnableSSID item, the network can be enabled or disabled;
the HideSSID section allows you to hide wireless network.

Rice. 8. Setting up the protection of the router.

If there is a Security section in the settings menu, where you can select a WPAPassphrase encryption key with a length of 8 to 32 characters.

As well as the Authentication encryption type and the appropriate WPAEncryptionAlgorithm information transfer protection algorithm.

When setting a password, you should be guided by a number of rules.

First of all, choose a combination consisting of at least 8 characters, including both lowercase and uppercase letters, as well as numbers.

In addition, it is undesirable to use the names and dates of birth of users as passwords.

Features of settings for different providers

Setting up ZTE routers is slightly different depending not only on the device model, but also on the service provider.

Among domestic providers, users most often choose the services of Rostelecom, Beeline and MGTS.

In addition to the fact that these operators have the maximum coverage of the territory of the country, a wide range of tariffs can be found in the list of their services.

When configuring the router to work with the Rostelecom network, you must not only enable Wi-Fi (according to the standard method), but also perform the following steps:

In the Mode column, set Mixed (802.1b+802.11g+…);
In the Country paragraph, put Russia;
In the Channel section, Auto is selected;
Transmitting Power should be set to 100%.
After completing these items, configure the Multi-SSIDSettings section. To do this, first check the box EnableSSID, in the column ChooseSSID - SSID, in SSIDName - the network name is selected.

For the correct operation of the ZTE router, which must work in the MGTS or Beeline network, the same steps are performed as in standard setting connections.

That is, entering a password and login, activating Wi-Fi and setting the parameters of the Multi-SSID sections. At the same time, routers of this brand are no longer used for ADSL connections.

WiFi router ZTE E5502 overview of interface settings

Setting up a ZTE router is an important step in connecting to the Internet. Detailed instructions for setting up your router

ZTE routers are known to Russians. Megafon provides subscribers with mobile options that catch exclusively the cellular network. The reception speed reaches 150 Mbps. The modem distributes wireless Internet. The portable option is often the choice of remote relatively small settlements. Residents of Udmurtia are now familiar with the MR150-5. The region to the north of which is only forests and tundra.

Chinese ZTE products are characterized by relatively low cost and availability. The advantages of 4G mobile communications were appreciated even by prisoners. Recently, attackers tried to transfer 29 ZTE routers to the Tula colony. The valiant law enforcement officers managed to prevent an illegal transaction. Let's see how exactly the router is configured. Often the audience is interested in instructions for changing the password.

Briefly about ZTE

In addition to routers, mainly mobile, feeding subscribers with a network from Wi-Fi, the Chinese corporation supplies a full range of user equipment, including set-top boxes digital television IPTV. More than half of the manufactured products serve provider networks. Many Chinese telecommunications service providers now use domestic equipment.

The history of ZTE company exceeds 30 years. One of the investors was the Ministry of Aerospace Industry of China. Initially, consumer goods were the main source of income, but the booming communications industry overwhelmed the government-managed enterprise with orders relating to cellular networks CDMA. In 2006, 40% of the company's income related to operator equipment. At the same time, proposals from foreign companies poured in. The first was the Canadian Telus.

A year later, Chinese equipment was ordered by Vodafone (Great Britain), Telefonica (Spain), Telstra (Austria). The client base of 2008 contained customers from 140 countries of the world. ZTE took the third place in the market of manufacturers of GSM communication equipment (about 20% of world sales). Gradually, the company mastered the production of smartphones. Corporation engineers have filed over 48 thousand patents, only in two years (2011-2012) 13,000 were confirmed.

Sometimes the company's equipment does not work ...

Define title

First of all, determine the true name of the device. For example, MF920W providers are called as follows:

MTS - 835F
Yota-MF920
Megaphone - MR150-5

A thorough study of the issue will help you choose the right firmware. An incorrect version can cause the device to malfunction. Such iron does not turn on, a flashing is required. By the way, an advance study of the forums will show potential buyer current model issues. For example, the one mentioned above is often devoid of charger, there is no antenna output. Therefore, for a summer residence, choose a different model. Additional bonus- the modem refuses to identify amateur flashing utilities.

The nuances noticed by users will sometimes become the main criterion. A clerk of a communication salon interested in sales is unlikely to advertise the dark side of the equipment. For example, MF823 requires a Beeline card with a USIM sticker. Otherwise, 3G technologies are used instead of the fourth generation. There are no updated firmware versions.

Common Problems

Saving readers' time, a caring admin installed a plug-in that draws convenient navigation according to the generated subheading tree. Therefore, we will devote a separate small section to each problem. ZTE mainly produces mobile modems, sometimes supplementing with a GPON fiber optic line interface.

Doesn't turn on

First of all, we remember whether a flashing was carried out. Unsuccessfully carried out manually - the operation completely removes access to the router. It is noteworthy that the appearance of the device (indication, illumination of the Ethernet interface) is the same. However, it is impossible to connect the equipment to the PC router. The browser writes: Unable to connect.

Hardware button Reset reset powerless to solve the problem. The firmware should be updated. Reliable manufacturers supply specialized utilities helping savvy technicians solve the problem. However, the Chinese manufacturer is still silent. Hackers have released the ZTE Unlocker utility, but the interface deals exclusively with the issue of unlocking (decoupling from a specific provider). The software actively exploits the diagnostic port specification.

An operable device understands the language of the terminal, including command line Windows. Operating system allocates a virtual directory to the device, inside which commands stored by the router's memory are executed. For example adb shell. However, the standard control paths will refuse to help restore the firmware on the router. Enthusiasts offer the following option.

Sometimes the desire to unlock is caused by another. For example, the developer removed support for the FTTB protocol on the H108N model. All interface users were forced to rollback immediately. Only now ... the manufacturer posted one utility - an upgrade. One way ticket.

Recovery utility

Often a broken ZTE modem is identified by the diagnostic interface. The official website (ztedevice) provides owners of the MF30 (Beeline) with an update utility only. There are no other models at all! The site 3ginfo.ru offers those who wish to download: “Kit recovery ZTE MF30".

Now the folder containing the previously unpacked firmware image needs to be corrected. The software read the device's memory, correcting the contents of the internal directory. However, the utility is powerless to enter IMEI. Therefore, edit the Channel1.nvm file yourself. Enter the correct IMEI.

Now run any flashing utility (for example, 3ginfo.ru/downloads127.html). Feed the program the files, including the edited Channel1.nvm. Now the router is finally restored.

A similar sequence of actions helps to revive some other mobile access points (for example, MF90).

JTAG

It helps to bring life back to many dead devices. Let's briefly describe the essence. In the 1980s, integrated circuit switching standards were deprived of a debug interface. Therefore, in 1985, a special JTAG group was created to solve the problem. The industry standard became commercial (IEEE 1149.1-1990) in 1990. Intel immediately provided the 486 generation with a debug interface.

Now the standard is used by electronics manufacturers everywhere. Initially, the interface belonged solely to testing purposes. Then the possibility interested debuggers, including the level of machine codes. Later, manufacturers guessed to exploit JTAG by updating the firmware of flash memory chips. Real boards use the number of pins:

5 and so on.

The latter options are more often used in the presence of many parallel-connected microcircuits. The first option accompanies the star topology. Therefore, the problem is limited to calculating the location of the pins of the JTAG port. Modern interfaces often contain 10 or more pins, so take the trouble to find technical documentation that reveals the meaning of pads. The contacts themselves are round or rectangular in shape, more often located along the edge, sometimes in two rows.

It is difficult to find a pinout, since the subject is the bread and butter of repair shops. Try to puzzle thematic forums (for example, gsmforum.ru). You will also need a full memory dump, take, for example, here 4pda.ru/forum/index.php?showtopic=255231&st=3040#entry36468746. The current memory dump (in reserve) is merged with the H-JTAG utility. You will need an adapter connector (the type is entirely determined by the utility used for recovery). Craftsmen usually adapt the now obsolete LPT. Solder the adapter with shunt resistors, get specialized software (for example, Z_Flasher Reanimator is used to restore cellular USB modems).

A memory dump by Giveio helps to find out the type of processor. This will be needed later when flashing. So, for work you need:

Utility Reserve copy current memory dump.
Compatible firmware version of the modem. Try going to byfly. The FTP server provides certain choices: H208N, ZXHN H208L, H201L, W300. By the way, the Belarusians took the trouble to put a beginner resuscitator kit, including instructions, in the server's shared folder (ftp.byfly.by/byfly/firmware_modem/ZTE/).
Flashing utility via JTAG interface.
DIY connector. Detailed requirements for the adapter are presented by the utility. Above was an example of using LPT.

Along the way, they exploit the capabilities of auxiliary software. For example, determining the type of processor.

Won't let you into settings

The live router is available through the browser, or interfaces remote administration(TelNet, SSH). However, the admin panel does not launch inside. Probably the factory settings have been changed. After making sure that you have the provider's password written down, try resetting the device with the Reset key (otherwise you will lose the Internet until your mother arrives). Then the previous characteristics of the equipment will return:

IP address.
Login.
Password.
SSID, Wi-Fi security key.

Refuses to share Wi-Fi

Ukrtelecom subscribers filled up TP with complaints: ZTE H108L refuses to connect wireless (wireless) subscribers. You will need to change the settings.

Open the admin panel (192.168.1.1 in a browser).
Enter login/password (admin).
Click Administration → System Management → Restore Factory Settings.
Apply changes, wait for reboot.
Re-enter your ADSL connection login/password.
Set the following settings on the page Administration → TR-069:
1. ACS URL - https://localhost
2. Login - loose
3. Password - 12345678

Port forwarding

It is often required from the outside to puzzle a home PC, to organize a server. Network protocols use polling ports of communication. The modem was originally built to protect against hackers. Access inside (Intranet) is completely absent. Therefore, port availability needs to be configured. We will demonstrate the technique of making adjustments, enlisting the example of H118N.

Note. The specified model shares Ethernet. The previous one (H108N) has two interfaces: FTTB, ADSL.

The simplest option to overcome Rostelecom hardware is to use the built-in Application menu. Enable the UPnP subkey. The port number is given as a number. A little lower is a specialized section. The Port Forwarding menu will help you set the desired numbers. Make sure to check the Enable box.

The third way is to set up a DMZ. Creating a dedicated service helps limit the damage of a possible hacker attack. Previous settings:

Connection type + port (in one line).
The local IP address of the PC.

Note. Port forwarding is sometimes referred to as port forwarding by translators.

First check the functionality of the externally provided service within the network. Helps reduce setup time.

Unlock

It happens that sometimes the subscriber wants to change the provider. I bought an MF823D, I was impatient to switch to Iota, or I got tired of MGTS, and the F670 refuses to eat someone else's SIM card. To change the service provider, the hardware must be unlocked. Megaphone MF823 calls M100-3 - the essence is the same. Unlocking is closely related to flashing issues. A binary image that is not tied to a provider is selected.

Attention! Before flashing, carefully study the forums. Some homebrew versions of the software break part of the functionality. Example - H118NV2.0.1d_E04_OV DOMRU removes the web interface (via browser). Telnet access remains. Have to reflash.

Briefing: Model MF823D

You will need a firmware image. Get it using search engines.

Download the PuTTY terminal emulator.
Install the ZTE diagnostic mode driver.
We turn on the equipment.
We feed the browser a fancy link 192.168.0.1/goform/goform_process?goformId=MODE_SWITCH&switchCmd=FACTORY.
The modem will send a response containing the line OK.

The hardware should go into diagnostic mode. Check by opening the Windows Task Manager. The properties contain the serial port number, opposite the corresponding COM there should be an inscription ZTE Diagnostic Interface.

Open the PuTTY terminal, copy the image to the serial port, the number of which is shown by the task manager. It remains to get the device out of the diagnostic mode. Open the terminal again, set the mode parameters:

Protocol - Serial (serial port).
COM line number (according to the Task Manager information above).
Try setting the speed to 921600.

The terminal window will be completely blank. Type in the commands one by one, each time I press Enter:

AT+ZCDRUN=8
AT+ZCDRUN=F

Each time, a device response may occur containing the number of successful, failed operations. Operation completed. Reboot your device.

Modem ZTE MF90+

Install the router following the instructions.
We open the admin panel through the browser (m.home, or the IP address specified by the manufacturer).
Set up Wi-Fi access. Open the web interface (by entering the admin login/password). Leave one device in this position. Later it will be possible to use the graphical shell, although the PC connected by cable will no longer open the menu.
We feed the browser (via cable) the lines for switching to diagnostic mode: m.home/goform/goform_process?goformId=MODE_SWITCH&switchCmd=FACTORY.
Successful completion of the operation ends with a response (“result”:”FACTORY:ok”).
Device Manager now contains unrecognized objects. Requires a diagnostic mode driver. Install the required software.
Once the devices are identified, the question marks will disappear. Select ZTE Mobile Broadcast Diagnostic Port. Look up the number among LPT/COM. Find out the exact name, eg COM9.

We find the image of the firmware. Open any terminal (including command Windows line). Copy the image from the directory to the serial port defined earlier. For example:

copy /b<имя_образа>\\.\COM9

Port number selection is illustrated earlier, the image name is known, including the location. The /b prefix means the binary mode of the transfer operation (because the firmware file is in binary format). Reboot your device.

To configure any of the routers of the ZTE line, it is first recommended to prepare the authorization data for the Rostelecom Internet connection, since it will not work to activate the network without them. In most cases, the provider uses the PPPoE type of service connection. These parameters are used to establish communication using ADSL and Ethernet technology. There are also less common options for connecting services that can be used when running a fiber optic cable directly to the client's apartment or private house.

Configuring Rostelecom parameters for ZTE brand routers

ZTE is one of the largest companies in the global electronics market. In addition to the manufacturer’s smartphones, which have recently gained immense popularity, which have a lower cost than similar products from the LG and Samsung brands, but are not inferior to them in terms of characteristics and quality, the company also occupies a strong position in the field of network equipment.

ZTE provides its customers with a wide range of devices to create a home or corporate network. For users who need the Internet outside the city, where there is no way to create a wired connection, the manufacturer offers ZTE MF 190 modems distributed both with native (factory firmware) and with an already built-in modification from Rostelecom.

These can connect directly to a computer or with the help of routers that support the appropriate connector and technology.

Attention! There is no possibility to reflash ZTE MF 190 modems from Rostelecom or other operators using official methods. For such tasks, the Dc-Unlocker program is usually used.

Also in the line of network equipment, ZTE also has routers, for example, H108N, adopted by users as an Ethernet modem for Rostelecom to set up high-speed home and work networks.

Preparing to set up the equipment

Before setting up ZTE routers under Rostelecom, for example, the E5501 model, you need to check the equipment package, which contains:

power supply (12V converter);
at least one Ethernet cable.

Of course, in the newly unpacked box from the device there will also be a software disk, a warranty and a lot of literature, but these components do not play an important role in setting up a ZTE modem under Rostelecom.

Attention! Even if you want to use the Internet only via Wi-Fi, an Ethernet cable is in any case an indispensable component that is needed for initial setup.

To connect the device, the first thing you need to familiarize yourself with is the ports on the rear panel.

Having deployed the ZTE E5501 side with functional connectors, as on the ZXV10 W300, here you can find:

four LAN ports;
Ethernet port;
connector for the power cable.

The ZTE H108N model will have one difference from the above modems, namely a connector for an ADSL cable (telephone cable), since this router is designed for Internet over a telephone line. This will not significantly affect the overall sequence of connecting network equipment. First of all, we connect the power supply to the socket and the port on the router, and then we insert the Internet cable into the WAN or ADSL port (depending on the modem model, one of these ports will be present). Now we find the RJ45 connector on the computer (standard network input) and connect it using an Ethernet cable to the corresponding port on the router. Since in our case there are four connectors, you can connect the cord to any.

Attention! If the ZTE H108N is configured, then in addition to the described sequence, it is also recommended to connect a splitter that filters the Internet and network signals. This will allow you to use two provider services at the same time.

When all the cords are connected, it will be possible to turn on the equipment, which is done using the button on the rear panel.

Now let's move on to the front of the device. It contains indicators that will help you find out about the status of options when setting up ZTE ZXV10 W300, H108N or E5501 modems for Rostelecom. For example, here is information about:

in which of the connectors is the computer connected;
is Wi-Fi working;
whether there is a connection to the provider and the Internet.

Setting up an Internet connection on ZTE ZXV10 W300, ZTE H108N, ZTE E5501

When the connection part is completed, you can proceed to setting up modems for Rostelecom, which we will do using the ZTE ZXV10 W300 as an example. We go from a computer connected directly to the modem to the browser and write in address bar router IP. You can find it in the equipment passport. In our case, it will be 192.168.1.1. Now we enter the standard login and password, which are also indicated in the instructions for the modem (admin / admin).

After that, you will be redirected to the device software control panel. In the Network tab, select the WAN parameters and make PPPoE setup connections according to the data provided by the provider. They can be found in the contract or on a special Rostelecom card.

Because the hardware supports wifi settings and such a modem is usually bought with the intention of connecting to the network wireless devices, you can configure the module operation on the Wireless tab. Here we select the network name (SSID), and also create a security key that will prevent unauthorized clients from connecting to your wireless network.

From ZTE, depending on its type (portable or stationary), it is produced in several stages. In the case of installing routers for private apartments or small offices, a suitable place is first selected, then the connection is made, and after that the connection parameters are entered.