photoshop

New miui version for jiayu g5. Everything about everything: cool selection

And so we have a device Jiayu G4S Advanced 2GB/16GB/3000mah, after unsuccessful manipulations, the phone does not turn on hangs on the splash screen Jiayu- "semi-brick"
our actions:

1. Turn off the smartphone

2. Remove the back cover and remove the battery

3. We install drivers on the PC, I have all the drivers, you will need to download all these drivers and install
we also download the official firmware, for example, I chose G4S-20141022-222444_Android_4.4_V6.0-FT - for the USB flash drive

4. We connect to a verified PC USB-lace, my smartphone cord Nokia with notice USB-B and now (attention phone without battery connect to the PC, then insert the battery, the phone should be defined as a device mtk, new equipment is found, the equipment is installed, since you have installed all the drivers before, everything will become without problems.

5. Disconnect the phone from the PC, remove the battery
Next, download and run SP_Flash_Tool from this site, where you can always download the latest drivers and program version.

6. Having opened Flash Tool click in the area and select the scanner file in the folder with the firmware.

7. Attention in the left tab, select Firmware Upgrade and nothing else would otherwise be a brick.

8. Click Download then take the phone and connect it to the PC in the off state without a battery, wait .... 1-2 minutes while the pro scans the ports to determine the port to which the phone is connected ... the bottom bar will inform you about the firmware status, patience, at the end a green square with the inscription OK will be displayed. Only then disconnect the phone from the cable.

9. We insert the battery, close the lid and turn on the phone, the first turn on will be longer than usual, again, patience.
If you are satisfied with the stock native firmware, leave everything as it is and use
if you want to put a custom one, then move on.

1. So, turning on the phone, go to the settings and turn on the root access R.

2. Download 2 files this is Mobileuncle MTK Tools with support mt6752 v 3.1.4 and custom recovery for the first revision I have a device with Rev-1 and throw them into the root of the memory card.

3. install Mobileuncle MTK Tools, click on the recovery update menu tab, after scanning the card, it will highlight recovery.img, click and reboot.

4. Downloading current version Miui firmware from offsite. And we drop the downloaded zip file into the root of the memory card, insert it into the phone.

5. With the phone turned off, hold down the volume and power keys at the same time VOL+&POWER wait until the splash screen appears TWRP let go.

6. Looking forward to the tab WIPE we go in and do all the swipe wipes cache data dalvik

7. Then go to the install tab INSTALL we specify our zip file with the firmware, we make a swap and install it in just a minute, we reboot.

Congratulations you saved your phone and installed Miui 7.

So, dear users, you have decided to reflash your JIAYU S3, G5 or F2 smartphone. Before proceeding with this simple operation, you need to remember a few points in order to avoid various problems:

You perform all actions performed at your own peril and risk.
You may lose the official warranty from the company. But since this smartphone is not officially sold in our country, you can not be afraid of this. Unless, of course, the seller himself gave you a guarantee for the device.
Just in case, it is recommended to save all important data to external media or cloud storage. At a minimum, your contacts will definitely disappear after the firmware.
Use only original USB cable when connecting the gadget to a computer or laptop.
Charge your smartphone to at least 70 percent. What is it for? And everything is simple - Jiayu can simply stop working, as the battery level has dropped. Then you will have problems with the operation of the device, perhaps even you will get a "brick" (that is, a non-working device).
Since you will be downloading a large amount of data, use unlimited tariff plans to access the Internet. Or track the used traffic on a limited plan. Otherwise, you may receive an unpleasant invoice for payment of communication services.
There are two ways to flash - an official update and using a third-party utility. For example, the F2 device is flashed here using an official update, while the other two are flashed using third party programs and applications.

If you have carefully studied all the rules and recommendations, then you can, in fact, proceed to the flashing process itself. Do not forget that this may take you some time, so in a hurry, in no case proceed to this. Especially you do not need to upgrade if you are waiting for an important phone call or something similar. Since the device at this time will be completely unavailable. It is advised to rearrange the SIM card to another phone if possible.

JIAYU G5 Firmware

First of all, we check installed recovery on the JIAYU G5 device. If you have a custom one, then you can go directly to the sixth paragraph of the instruction. V otherwise- start from the beginning. If you do not understand what, in principle, we are talking about, then most likely you do not need such a recovery.
Install the utility https://yadi.sk/d/YkC8rKE-347mSw on your JIAYU G5 smartphone.
Copy the previously downloaded firmware to your phone's memory card.
Now you need to download custom Recovery https://yadi.sk/d/VbS0qDeE347mKN and copy it to the folder next to the firmware. This is done for your convenience.
Now we launch installed application in the second paragraph. There you need to find a tab with a recovery update, where we select the file downloaded in the fourth paragraph. We approve all warnings and wait for the JIAYU G5 to reboot in the required mode.
If you were unable to enter this mode in this way, you can try the following option: connect your phone to a computer or laptop using a USB cable, turn off the JIAYU G5 smartphone, then simultaneously hold the power and volume up buttons for a few seconds (until the company logo appears ).
You are in recovery menu. Here you will need to make a backup and two wipes (wipe data, for example) to clean the phone. To navigate the menu, use the volume keys, and instead of the OK button there will be a power key.
Now select the install zip from sd card / choose zip from sdcard item, after which we find the firmware downloaded to the device's memory card in the third paragraph. Naturally, if the device asks you to confirm the operation being performed, you immediately agree.
It remains only to wait for the completion of the flashing. This process may take long time so don't get scared right away. Be patient, because you have put your JIAYU G5 smartphone under some stress! Get into his position and be more patient dear ones. When the firmware is finished, you can use your device again in normal mode.

JIAYU S3 Firmware

Download and install required drivers phone JIAYU S3 to a computer for their communication in the future. Otherwise, your laptop or PC simply will not detect the device, and the firmware will fail.
Now download and install special utility for flashing SP Flash Tool for the same.
We proceed to download the firmware file (can be official or custom) specifically for your JIAYU S3 smartphone model. If the documents are in the archive, then it is better to immediately unzip them into a separate folder on your PC.
Connect your device to the computer via the USB input and wait until the system installs the necessary utilities to communicate with the JIAYU S3 device. At the end of the process, you can disconnect your gadget and put it aside for a while.
Next, run the Flash_tool.exe utility as an administrator. Here we click on “Scatter-loading”, and in the new dialog box that appears, select the scatter.txt file from the firmware folder of the third item.
Go to the top main menu of Flash Tool and click on the Options tab, and then on the USB Model. Now to Option, then DA DownLoad All, then to Speed, where the end point will be the High Speed button. Do not worry, after a long torment you will have the opportunity to rest.
Turn off your JIAYU S3 smartphone and then click on the big button in the DownLoad Flash program (and “if ROM Firmware update, then Upgrade”).
Now connect the phone (do not turn it on!) to the computer and wait until the process of flashing your JIAYU S3 device is completed. This will be indicated by a window with a green circle.
Congratulations! You are amazing and you can safely turn off your JIAYU S3 smartphone and turn it on, but with new version systems.

JIAYU F2 Firmware

Here we will flash the JIAYU F2 device without using a computer, and this method is official update version of the machine's operating system. It will run directly from the phone itself without the need for a computer or cords.

First, connect to an available wireless network WiFi.
Now go to the "Settings" menu and find the "About device" item. Here we will need a tab called "Software Update". Click the update button.
If your smartphone writes that updates have already been installed on your device, then there are no available firmware for your JIAYU F2 device. That is, the last available version operating system.
Otherwise, you need to agree to download updates and wait for it to complete. When finished, click on the Install button. After that your samsung galaxy will start the system update, during which the device cannot be used. In no case turn off the JIAYU F2 phone, do not try to reboot, remove the battery - you can get a "brick", that is, a completely non-working device.
Only when you see the familiar home screen and the message that you have successfully completed the firmware update procedure, you can use the JIAYU F2 device normally.

Summing up

Today we have learned how to flash your JIAYU G5, S3 or F2 smartphone. Note that the method described with the last device can be applied to the rest. But in reverse side no need to move (the g5 and s3 ways may not fit together). Do not forget that if you are incompetent in this matter, then it is better, in general, not to touch anything and leave this matter to professionals. If you have any problems, then we will definitely check whether you did everything right: perhaps you missed some point from the recommendations or missed a whole paragraph from the instructions. In extreme cases, contact a service center or workshop, where a specialist will definitely help you (if there is one, of course). Share your experience in the comments with other users, dear friends!

The appearance of the new Jiayu G5S smartphone has caused considerable excitement in the Russian-speaking segment of the Internet. Its design resembles new iPhone, and the filling is in no way inferior to the flagship models of branded manufacturers.

Large, bright, responsive screen, 8-core MT6592 processor ( clock frequency 1.7 GHz), 16 GB internal memory, 2 GB RAM, rear camera 13 MB, thin metal case, powerful battery- all these are good reasons to purchase a new creation Chinese brand Jiayu.

	Firmware:	https://yadi.sk/d/-GgtYfx9dKuGG
	Drivers:	https://yadi.sk/d/I_6kSDepdKrc9
	FlashTool:	https://yadi.sk/d/2ZlYwvoscZKCB

How to flash Jiayu G5S without fatal consequences?

To begin with, it should be noted that the Jiayu G5S firmware is a purely voluntary matter. If you follow the instructions, then you understand that there is a chance to aggravate the situation and turn your beautiful phone into a useless "brick". Do not experiment with this model unless absolutely necessary!

To update we will use special software– SP Flash Tool 5.

Unzip SP Flash Tool 5 to your computer.
Turn off your smartphone and make sure that the cable is disconnected from the PC.
Remove the battery from the smartphone.
Connect your smartphone to your computer via cable. At this point, the operating system should display a message about a new device. Help her install it - specify the path to the folder where the driver is located MT6592 USB VCOM.
Disconnect the cable from the PC.
Official firmware Jiayu G5S must be unboxed.
Run the program SP Flash Tool 5. Please note that the path to the folder where the firmware is located should not contain Russian or Chinese characters!

Firmware Upgrade

Download

Firmware Upgrade + Download

Connect your smartphone to PC via cable. If everything is done correctly, the program will see it and start the flashing procedure. If the phone is not detected, disconnect it from the PC, remove the battery, then try to connect it to the PC again.
After the end of the firmware, a circle will appear with the inscription OK.

IMPORTANT! Before starting the procedure, be sure to backup IMEI in any convenient way.

Jiayu G5 Advanced Edition runs under the operating system Android 4.2. Its performance is rated 3 out of 5 (in its segment). This smartphone is quite productive. The characteristics of the device are published here, instructions on how to reset the settings, flash the device and, of course, how to get root rights to jiayu

Root on Jiayu G5 Advanced Edition

How to get a root for Jiayu G5 Advanced Edition see instructions below.

Initially, try the universal utilities for getting root on MTK for G5 Advanced Edition

(root in one click)
(a collection of root utilities in one)

If it didn’t work out and SuperUser didn’t appear, then ask for help in a special topic

Specifications

Standard: GSM 900/1800/1900, 3G
Type: smartphone
Operating system: Android 4.2
Case type: classic
Body material: steel
SIM card type: regular + micro SIM
Number of SIM cards: 2
Weight: 158g
Dimensions (WxHxD): 63.5x130x7.9mm
Screen type: color IPS, touch
A type touch screen: multi-touch, capacitive
Diagonal: 4.5 inches.
Image size: 720x1280
Automatic screen rotation: yes
Scratch resistant glass: yes
Type of ringtones: polyphonic, MP3 ringtones
Vibrating alert: yes
Camera: 13 million pixels, LED flash
Camera Features: Autofocus
Video recording: yes
Front camera: yes, 3 million pixels.
Audio: MP3, FM radio
Dictaphone: yes
Interfaces: USB, Wi-Fi, Bluetooth
USB host: yes
Satellite navigation: GPS
A-GPS system: yes
Internet access: WAP, GPRS, EDGE, email POP/SMTP, HTML
Processor: MediaTek MT6589T, 1500 MHz
Number of processor cores: 4
Video processor: PowerVR SGX544
Built-in memory: 32 GB
Volume random access memory: 2 GB
Memory card support: microSD (TransFlash)
Additional SMS features: text entry with dictionary
MMS: yes
Battery capacity: 2000 mAh
Sensors: light, proximity, gyroscope, compass
Book search: yes
Exchange between SIM card and internal memory: there is
Organizer: alarm clock, calculator, task planner
Complete set: smartphone, battery, Charger, cable

Firmwares for Jiayu G5 Advanced Edition

Official android firmware 4.2 [stock ROM file] -
Jiayu custom firmware -

Firmware for Jiayu G5 Advanced Edition you can find in the branch In addition, first download the necessary software for flashing

What information do you need to know for flashing?

Make/Model [Preferred] - Jiayu/G5 Advanced Edition
Processor - MediaTek MT6589T, 1500 MHz
LCD Driver (Version)
Kernel (version) [preferred]

Before flashing and in the process of selecting firmware, check the base TX ( specifications) through the program

What are custom firmware(firmware)?

CM - CyanogenMod
lineageOS
paranoid android
OmniROM
Temasek's

AICP (Android Ice Cold Project)
RR (Resurrection Remix)
MK(MoKee)
flymeOS
Bliss
crDroid
Illusion ROMS
Pacman ROM

Problems and disadvantages of Jiayu smartphone and how to fix them?

If the G5 Advanced Edition does not turn on, for example, you see a white screen, hangs on the splash screen, or the notification light only blinks at all (possibly after charging).
If it freezes when updating / freezes when turned on (requires flashing, 100%)
Not charging (usually, hardware problems)
Can't see sim card
The camera does not work (for the most part, hardware problems)
Sensor not working (depending on the situation)

For all these problems, please contact (you just need to create a topic), specialists will help for free.

Hard Reset for Jiayu G5 Advanced Edition

Instructions how to do hard reset on Jiayu G5 Advanced Edition (factory reset). We recommend that you familiarize yourself with the visual guide, which is called on Android. .

Reset codes (open the dialer and enter them).

*2767*3855#
*#*#7780#*#*
*#*#7378423#*#*

Hard Reset via Recovery

Turn off the device-> go to Recovery
"wipe data/factory reset"
"yes - delete all user data" -> "Reboot System"

How to enter Recovery?

hold and hold Vol (-) [volume down], or Vol (+) [volume up] and the power button (Power)
a menu with the Android logo will appear. That's it, you are in Recovery!

Factory reset on Jiayu G5 Advanced Edition can be done in a very simple way:

Settings->Backup & Reset
Reset settings (at the very bottom)

How to reset pattern

How to reset graphic key if you forgot it and now you can't unlock your Jiayu smartphone. On the G5 Advanced Edition, the key or PIN can be removed in several ways. You can also remove the lock by resetting the settings, the lock code will be deleted and disabled.

Reset graph. blocking -
Password reset -

Jiayu G5 firmware

Bought a new one chinese smartphone Jiayu G5 and you are not satisfied with how it works or functionality? Want to reflash to new firmware? I will try to briefly and clearly tell you how to flash Jiayu G5 to a new ROM.

Everything you do - you do at your own peril and risk!
The author of the smartphone firmware manual and instructions is not responsible for the breakdown of the device in case of your wrong actions!

If you already have custom recovery installed on your device, you can safely skip steps 1 to 5 and go to the sixth step. But if you don’t know if you have such a recovery, do step 5, if it didn’t work out, then your Jiayu G5 has a stock recovery, then start from the first step.

And so let's start the process of flashing the Jiayu G5 smartphone to a new firmware or custom ROM.
0. The very first item is symbolic and optional. If the phone has important programs or contacts, SMS - install the “GO Backup Premium” program from the market and make a backup copy, saving it to a USB flash drive
1. Install on the phone a small program m44_toolbox_20130809_v2.9.5_en.apk

2. We download the firmware itself that we will install on the PC, I suggest you Lewa OS, then copy the firmware to the memory card.

3. We also download the custom recovery G4recovery_CWM_6.0.2.8_ENG.img (which will make it possible to flash our phone) and copy it to the root of the flash drive, next to the firmware (so as not to search for a long time)

4. In the program that we installed in paragraph 2 this manual, go to Recovery update and choose the recovery that you downloaded in step 3. Then you agree with all the warnings, the phone will reboot in recovery mode.
5. If suddenly something went wrong - you can enter the recovery even from the switched off smartphone by pressing the power button and the volume up key (+) at the same time, do not forget to insert the USB cable, which in turn is connected to the switched on computer (apparently this combination means something in China)
6. Going into the recovery, make Backup (moving through the menu with the volume control button, the power button acts as - “enter”
7. Then do all kinds of wipes (there are only two) which will remove all unnecessary information and clear the cache.
8. Go to install zip from sd card / choose zip from sdcard and select the very firmware that you copied from the PC to the USB flash drive, and confirm the desire to flash it.
9. We are waiting for the firmware process Phone Jiayu G5 is not fast and will take a couple of minutes (from 3 to 10) please note that there is no paragraph 9 and paragraph 2 is repeated, we wait, we wait, we wait, we wait ...
10. After the firmware is completed, the phone will reboot for the last time, the first boot takes longer than usual, so we are not afraid. Well, that's all, we are happy with the new firmware.