How to access the web page of the router. Remote access to the router via the Internet

Hello friends!. Today I will tell you how to enter the router or the router settings. I’ll tell you honestly, I myself used to think that there was only one router admin address, but it turned out to be wrong. By the way, here is another article on the topic, read on health. I am sure that if you were looking for this article, then you decided to set up your router yourself, otherwise you don’t want to pay money to the master to set it up. After all, it’s only there for five minutes. Let's start in order.

How to enter the router

1. Connecting all cables. To go to the router, we need to connect the cable that we go between the computer and the router. In the kit you should have a wire crimped on both sides with plastic chips, we need it. We connect it to the router to any socket (LAN) except WAN. Don't forget to plug your router into a power outlet. If everything is in order, then we will see that a green light will light up near the plug. We could connect to the router and through wifi connection, but not all routers support the initial configuration via wifi? so we connect the cable. After connecting the cable, it may pop out, but don't worry, it will disappear later.
   
   
2. Then we find out the address of the admin panel of the router. You can do this by going to 192.168.1.1 or 192.168.0.1 or 192.168.1.72 or 192.168.1.253. You can also see your IP address of the router admin panel under the bottom of it. There is always a sticker on which the MAC address of the device and the address of the admin panel are indicated. If you were unable to log in through opera or another browser, then we can do it manually. To do this, run to Next, find the Network and the Internet and go to this section. Click on Network and Control Center public access and choose from the menu on the right Adapter settings changes.There you will see all the connections that are on your PC. We need to choose Connection via local network and click on it right click mouse and select state . After we select the button Information and there we will open a window in which the address of the admin panel will be indicated. It is designated as IPv4 default gateway then we need to enter it in our browser and then you can go to the router.
   
3. Admin login and passwords. By default, to enter the admin panel of the router, you need to enter your username and password. Our login is always Admin and the password is either Admin or just leave an empty box. You can also try the password 1234, and if it doesn’t work out, then you have a used router and a different password was previously set on it. We need to reset it, read on how to do it.
4. Resetting the password on the router we can by pressing the reset button, and you need to hold it for 15-20 seconds. This button is located on the back of the router (see picture). After resetting the password, the username and password that I wrote above will already work for us.
   That's all guys! Now you know how to enter the router and its settings (admin panel). If my article helped you, write about it in the comments, and do not forget to click on the social buttons. I will be very grateful to you for this. Don't forget to read about it at your leisure.

In computer forums, a lot of attention is paid to fine tuning router, which allows you to significantly increase its speed and connection stability. However, many users are faced with a problem of a different order - they simply cannot go into their router settings in order to select the optimal parameters. There is no need to panic and go to the store for a new device, since everyone can solve such a problem. If the computer does not enter the standard menu of the router's web client, you need to try changing the connection settings or pay attention to other nuances.

We are looking for a way out if there is no access to the router settings.

By typing the web client address 192.168.1.1 in your favorite browser, you may find that the router does not respond to your command. To enter the web client menu, first take the instructions and read what address is set for the router by the manufacturer. Many electronics developers prefer to set the combination 192.168.0.1, which allows you to release the above address for another network equipment. Also, information about the base address may be contained on the bottom of the instrument case.

Try to change the web browser - the standard application gives the best option Internet Explorer, which uses direct connections without redirection. However, it may also display an error when trying to enter 192.168.1.1. You can increase the chances of a successful connection by using the RJ-45 standard cable that comes with your router. Be careful - it must be connected to the LAN port on the router, and not the WAN connector, which is most often highlighted in blue. To get unrestricted access to menu 192.168.0.1, be sure to disable the wireless adapter on a computer using a special function button or the network connection menu.

Fine tuning

If the computer does not enter the standard web client menu, it is quite possible that the connection error with 192.168.1.1 is caused by an address conflict on the network. First of all, you will need to enter the control panel of the operating system and find the “Internet Properties” item there, which can also be called “Internet Options”. Then you need to open the "Connection" tab and at the bottom find the button that is responsible for the local network settings. In the dialog box that opens after clicking it, disable the use of proxies in regular local networks and VPNs.

However, it is not always possible to establish a connection with 192.168.0.1. You need to open the properties of the used network adapter- There are three main ways to enter this menu:

• Through the "Network Control Center";
• Through the control panel - the "Network Connections" tool;
• Enter control netconnections on the command line.

Since the router has a web client address of 192.168.1.1 or an alternative 192.168.0.1, for the network to work correctly, an electronic computer must have a similar IP that differs only in the last digit. By right-clicking on the icon of the adapter you need, open its properties, in the dialog box that appears, select the IPv4 connection protocol and click on the "Properties" button again.

The general protocol parameters may contain an answer why the computer does not enter the standard menu of the router's web client. The IP may be different from what the router uses - to continue working you will need to change it using the same beginning as in 192.168.1.1 or 192.168.0.1. The number at the end must be between 2 and 254 so as not to create an address conflict within the local network. Of course, the best option would be to set the address automatically based on the needs of the computer, but this feature is not supported by every network. Don't forget to also set the gateway address on this tab and DNS servers- in these fields you will need to enter the numbers 192.168.0.1 or an alternative combination of 192.168.1.1, depending on standard parameters router.

Also, the computer sometimes does not enter the menu you need as a result of limiting the transmitted traffic within the created local network. Opening the menu 192.168.1.1 may be prevented by the antivirus you installed, which sets too serious control over user actions - you should simply disable it while working with the device settings. Access to the specified address or 192.168.0.1 is often blocked by the standard operating system firewall - it can also be disabled through the operating system control panel. After completing the above steps, you should be able to enter the settings of the router you are using, however, in certain situations, all user actions turn out to be ineffective.

Extreme measures

If the computer still does not enter the web client of the device, it is advisable to perform a complete reboot - for this, a small Reset button is used, which can be located at the back or at the bottom of the router case. It must be pressed with a long thin object (for example, a paper clip) and held for approximately 10-20 seconds, depending on the model of the wireless device. After full reset data, you can access all advanced device settings at the standard menu address 192.168.0.1, as well as an alternative combination of 192.168.1.1 - this is determined by the device model.

This method will also be effective if you have irretrievably lost data for accessing the web client or they have been changed by another person who received unauthorized access to the router settings menu. After the reboot, it is imperative to use the standard login and the preset password that is set by the hardware builder. Most often, you need to enter the word “admin” on both lines, but there are some exceptions. To accurately determine the correct login information for the standard web client, review the instructions for the device. Be careful, because after the reboot, all settings will have to be set again.

If, after resetting the router, the computer does not enter the settings menu at the menu address 192.168.0.1 or an alternative IP, try again using a different laptop or modern tablet. It is possible that the inability to access 192.168.1.1 is caused by incorrect setting network card or damage to it. In the first case, you should try to restore the drivers or use the proprietary distribution of the operating system from the developer of the smart machine. In the second case, you will have to change the wireless module.

The source of your problems may also be a malfunction of the router itself - usually the problem of the inability to access 192.168.1.1 is solved by a simple flashing wireless device. Remember that you can enter the web client menu without interference only if you download the software from a trusted source - it is best to use the resource global network or the file server of the router manufacturer itself. Also, the router does not enter the standard settings menu using the 192.168.0.1 combination and if the components are completely broken. Such a device is always easier and cheaper to change than to repair. When choosing a new device, be guided by the characteristics of its power and antenna gain, as well as the ability to work with certain types of networks.

If the device is damaged, but you need to create a wireless network for a short time, you can use the corresponding function of the adapter in the computer. To do this, you need to install the appropriate software - good option will be Virtual Router Manager. After launching it and correct setting The electronic computer will independently distribute traffic through the wireless network, although the possibilities of such connection will be limited. For example, it will definitely not work to achieve high speed and long range of the network. In addition, during this time, the device will not be able to connect to other wireless networks.

Problem solving

The statistics provided service centers, shows that in 90% of cases the problem with the inability to access the web client can be solved by simply reconfiguring the router or computer. The user should pay special attention to the network settings - most often the cause of the malfunction is an address conflict in the computer environment. Also, the impossibility of access is often due to traffic restriction by an antivirus or a standard firewall, so it is advisable to disable such protective applications before working with wireless network settings. However, there are also troubles associated with the failure software router - the device will need a reboot or re-flashing. Finally, the root of the problem should be looked for in the malfunction of the device itself or the network adapter of the computer - unfortunately, if they break down, you will have to purchase new equipment.

Without using an access point, it will not be possible to create even the simplest home network. The default settings set by the manufacturer may not match its functionality and security. It is possible to change the configuration, set up security and other options through the control panel of the router, but for this you first need to log in there.

Go to the router settings and set the necessary parameters equally easy for devices different manufacturers. Beginning users may have some difficulties, but using this instruction to find ways to solve them will not be difficult.

We connect the equipment

Let's consider a standard situation that does not require the installation of network card drivers, its configuration, determining the IP address via command line and other manipulations. In 90% of cases, you can do without them. A separate chapter of this article will be devoted to problems that arise during the process of logging into the router.

What you need to connect the router:

• Network cable that comes with the equipment (any lan cable will do, except for wires crimped for direct connection of two computers);
• The presence of a network adapter on the connected computer or laptop;
• The router to be configured.

The hardware installation process is as follows: network cable plug into the appropriate connectors on the router and computer. On a PC, this is the RJ-45 port located on motherboard. Almost all computers and most laptops have at least one such connector.

Routers have 5 or more network ports (on very budget models 3). connector of blue color(under it there may be inscriptions: WAN / line / Internet) is designed to connect the provider's cable, or any other cable through which the Internet "enters" the router. Other network ports are used to enter the router control panel. They are usually yellow and signed "Lan1", "Lan2" and so on - how many ports, so many numbers.

The power wire of the access point is connected to the appropriate connector, and to start it, just plug the adapter into the mains.

How to get into the router interface

The router is an independent device that does not require additional drivers or other software to be installed on the PC. In fact, this is a small computer. It has a processor, RAM, and even an operating system.

The CD supplied by some manufacturers does not contain drivers. There is a utility on it, the purpose of which is to control the device through its own interface. The use of such software will not be considered within the scope of this article. Since there is a simpler and universal way access point settings.

You can access the router's control panel through a browser by entering its IP address in the address bar: 192.168.1.1 or 192.168.0.1. The exact network address of the access point can be found on the bottom of the device.

Video instruction for entering the interface:

You can change the parameters of the equipment both by connecting via a wire, and via wireless connection.

Login to the admin panel using a PC

You can access the router settings from your computer using a cable connection using any browser, for example, Google Chrome. After entering the IP address of the access point into the address bar, the user authorization page will open. The default data can be found on the label on the bottom of the router. The most common username and password is admin. They are entered in the appropriate fields, after which you need to press "enter" or on the "Login" button.

If the entered values ​​are correct, you will be transferred to the personal account of the equipment control panel.

Wireless connection from mobile devices

It is not always possible to view the access point settings on the computer. For example, there is no time to turn it on or you don’t want to look for a cable. If a Wi-Fi network is available, you can control the router from a laptop, tablet or phone that has a program for viewing Internet sites.

The sequence of actions is the same as on a PC, the difference is in the method of connecting to the network. To connect to WiFi networks new access point, no password is required. Phone or tablet will detect desired network, after which it remains only to join it. Next, you need to launch the browser and in it address bar enter the IP address of the router, for example, 192.168.0.1, after which the authorization page will open. On the mobile android phone it looks like this:

To open the control panel, you must enter the standard login and password.

Hardware configuration is no different from the same process using cable connection. Using Wi-Fi, you can change the settings of an old device or set up a new one. The only operation that should not be done over a wireless connection is flashing the system or restoring it from a backup file.

If something doesn't work

If you do not go out to get into the settings, the sequence of actions depends on the problem that has arisen. The most common situations are when the computer does not “see” the connection at the router address (the page is not available in the browser) or it is impossible to enter the admin panel (incorrect username or password).

The page is not available

After entering the IP address, the browser does not enter the control panel page for the following reasons:

1. Registered static IP. To check the address of the router, you need to know where the corresponding parameters are located. In Windows, you need to go to the "Network and Sharing Center".

In the window that opens, on the left, click on the menu item "Change adapter settings".

In the next window, select your connection. You can manage the parameters by right-clicking on it, after which you need to select the "properties" item in the drop-down menu.

The page displays the components used by this connection. You must select as in the window on the left, after which the window on the right will open.

In the properties menu of the TCP / IPv4 protocol, select the option "Obtain an IP address automatically" and then click "ok". If any numbers have been entered in the address, subnet mask, and default gateway fields, write them down just in case.

1. IP address not known. To find out, you can use the tools of Windows OS. To do this, select the “Run” item in the “Start” menu (or press the “Windows + R” combination), type “cmd” in the window that appears, then enter “ipconfig” in the console command line, as a result the following should appear:

The IP address of the router is underlined in red.

Unable to login to admin panel

There is a situation when, after entering authorization data, the browser gives an error - “Invalid login / password”. To solve this problem, you can first experiment with the input. Try different options, for example, the password could be 1234 or password. The password field for some manufacturers does not need to be filled in by default.

If the fields are filled in, and after pressing the "Login" button or the "enter" key nothing happens on the page, you should try logging in from a different browser or restarting the router.

For what reasons I can’t log in - informational video:

Standard settings decorate the label. The list contains IP-address, login, password. Open a browser, enter 192.168.0.1 (less often 192.168.1.1), the admin panel will allow you to perform typical settings. The technique works exclusively through local ports, including the Wi-Fi interface. Therefore, any neighbor, passer-by can enter. Protect the web interface carefully.

There is also access from the outside, but access to the router must first be opened. The actual instruction is determined by the manufacturer. For example, when going into the Smart Box Beeline settings, we see (section About this router) the Allow link. After the reboot, the equipment will ask you to enter the IP address (port 8080 is selected) of the control station. Extreme options are available: any (255.255.255.255), complete ban (0.0.0.0). The port value can (even should) be changed, avoiding the assignment of numbers used by standard services.

Remote Access Restrictions

Any PC on the Internet receives a unique IP. The IPv4 protocol limit is estimated to be 4,294,967,296 machines. The conflict is almost out of the question. However, a new requirement is looming: the router must have a unique, externally visible identifier.

The network address is assigned by the owner. For example, the type of IP of the local network is often the following: 168.0.X

It is impossible to view the computer identifier from the outside using direct methods. The numbers contain a routing table hidden RAM devices. However, the user from the outside is powerless to legally obtain the configuration. Host computers, visiting a specialized site that determines IP, will see an identical picture. The numbers match!

Similarly, sometimes the provider refuses to give subscribers unique combinations. Instead, "gray" addressing is used. Then it is impossible to get into the menu from the outside.

Having obtained a "white" address, connect from the outside using known numbers. There is only one problem: most providers re-assign after a reboot. Therefore, the current configuration should be closely monitored.

Standard variant

Remote access is pre-authorized. Here is a list of settings:

• Login: Password.
• Connection port. The provider sometimes blocks the most common attack ports. The ftp(21) service often suffers.
• The IP address of the future administrator (or the total permission of all options by selecting the value 255.255.255.255).

After that, from anywhere in the world, opening a browser, typing the IP address of the router, setting (through a colon port) is able to connect for configuration.

Loophole

Enthusiasts Suggest a Workaround: Installing Specialized Software remote control on a PC (like Remote Desktop Windows desktop). For example, Team Viewer. The process goes indirectly:

1. Remotely open the desktop of your own (turned on) PC.
2. Through the browser you can go to the settings.

Standard local (browser) option

Connect with a cable to any internal port (LAN), or use a wireless protocol (Wi-Fi):

1. Visit the page personal account router by feeding the corresponding IP address to the browser.
2. Enter login/password.
3. Take the necessary actions.

telnet

The protocol is widely used to organize two-way communication between devices. Sometimes used special application(Terminal), more often - the command line. Linuxoids tear off the built-in terminal of the environment (the name is given above Windows programs). The connection uses the TCP protocol, oriented to bytes 8 bits long (standard values).

Story

Telnet was the first protocol (1969) used by the creators of the US defense network. Described in RFC 15. STD 8 (1983) provided computer scientists with a powerful means of communication. The original name is formed by two words:

1. teletype
2. network

Recall that a teletype is a remote printing press controlled by digital signals. The use of such tricks greatly saves traffic, requiring minimal cost bitrate. In 1969, BBN supplied 4 communication interfaces (similar to a software-controlled router) to the US Army. On October 29, the test took place. The story is carefully hushed up, but the book The computing universe: A journey through a revolution (Tony Hay, Gyuri Popeye) reveals the details ...

“The protocol for the interaction of a giant computer with a network communication interface was developed in the spring (1969) by Robert Kahn (BBN Report 1822). In Los Angeles software implementation students chosen by Kleinrock (Steve Crocker, Vint Cerf, Jon Postel, Charlie Klein) took up the challenge. The guys found it amusing to fulfill a defense order during the training period.

Software for the interconnection of the four interfaces was also taken up by students calling themselves the Network Working Group, who issued a series of notes, Requests for comments, which became the beginning of the RFC family of standards (see above). The interaction of dissimilar calculators required the introduction of general agreements, called the protocol. The word was borrowed from the ancient Greeks, it denoted the first sheet of manuscripts, which gave the content, dates, names of authors. The programmers outlined the header formats.

The bottom layer of the protocol described the frame structure. The first applications were consoles for remote control of calculators. Along the way, the first analogue of FTP appeared for transferring files. Remote application got a new name Telnet.

Sigma-7 (Los Angeles) sent the first word (login) to Scientific Data Systems 940 (California).

Usage

Readers have already guessed: the administrator connects through the command line, repeating the experience of American students in 1969. Any terminal shell is suitable, or use the regular one:

1. Windows:
   • Start menu.
   • Service section.
   • Right click on Command Prompt.
   • Run as administrator.
2. Linux: Ctrl + Alt + T. Prefix commands with sudo.

Note! Sometimes Windows component, which is responsible for implementing the protocol, is disabled. Enable the option. In the search bar, type "turn features on or off", find the Telnet Client, check the box, click OK.

Dial: telnet

Leave a space after the address. You will be prompted to enter a username and password. Only a router that supports the protocol, such as DIR300 ( latest version firmware). Appearance interface is defined by the developer, universal instruction no.

Examples

Consider a few examples of configuration and management.

Zyxel

1. Visit the System section of the Zyxel modem admin panel.
2. Telnet section.
3. Check the Enable checkbox, enter the port number.
4. Download the PuTTY terminal emulator.
5. In the Session section of the program settings, enter the IP address, plus the port number. Select the Telnet protocol with the radio button.
6. When entering the modem, enter your login, password (usually admin).
7. Configuration mode is started by typing configure terminal.
8. A complete list of commands is provided by the official manuals.

SSH

The first terminal protocol sent plaintext. Hackers can easily intercept the broadcast. However, the U.S. defense industry has been a fearless sparrow since the launch of Gagarin. The attackers appeared much later. The application layer protocol (OSI hierarchy) SSH corrects the specified defect. The client-server shell is supported almost exclusively by professional routers.

Data transmitted over the Internet is encrypted so that hackers cannot intercept the process. The SSH system is considered native to UNIX-like systems, Billy Gates (2015) promised to introduce support for Windows.

Story

The first version appeared after the release of Windows (1995): a researcher at the Helsinki University of Technology got hacker sniffers that steal passwords. Telnet clearly failed. The rest of the protocols - rlogin, ftp, rsh - didn't help much. There was no strong authentication system.

The July 1995 release was completely free. Therefore, the new (1996) year was met by 20,000 newly minted users of Finnish software. Tatu Ylönen immediately created a community. Subsequent versions of the protocol became proprietary. The Millennium has already caught 2 million people who want to classify their credentials.

2006 brought the second version of SSH to the world. New algorithms exploited the advantages of the Diffie-Hellman protocol. Now the admin could run several sessions in parallel. The idea was picked up by the RFC committee.

In parallel, attempts were made to develop open source software. Developers (1999) shook up version 1.2.12. The idea was picked up by the creators of OpenBSD, providing the next release (2.6) with the OpenSSH extension. There is a tendency to transfer collateral to other OS. Today, development is considered cross-platform.

Example

The theoretical aspect positions SSH as an attempt to find protection against hacker intervention in the router. The TP-Link guide suggests downloading PuTTY. There are 2 authorization methods available:

• Login: Password.
• public key.

SSH communication must first be allowed. If physical contact is not possible, log in via Telnet for the first time (using the ssh server command). The list of SSH commands is provided by the router manual.

Attention! The router must support the selected encryption type (AES, Archfour, 3DES, Blowfish…).

Password access

After setting the permissions, open the PuTTY terminal:

1. When setting up a session, enter the IP address, port.
2. Set the protocol type to SSH.
3. Use the commands given by the manual.

public key

1. Run the key generator from the PuTTY distribution.
2. Select type, length (512-3072).
3. Generation will require the efforts of the operator: randomly move the mouse pointer.
4. Save the public and private keys on a TFTP server.

After that, the public key can be downloaded if you have access. For example, using the telnet console. Once you have the key, save the file, then:

1. Open a PuTTY terminal.
2. Enter the router's IP address, port number.
3. Take the trouble to set the path to the file (section Connection - SSH - Auth).
4. Login required.
5. If it doesn't enter, the key is rejected. Generate a new one, upload, download. You should check the path of the folder where the key files are located.

Fiasco

I can’t log in, settings don’t open - follow hard reset router.

• Locate the reset hole.
• Press the button with a match, hold for a few seconds.
• Wait.

The reset values ​​are on the sticker. You should open a browser, go to the specified IP address, enter your login / password, configure the network properly.

A router failure may occur after an incorrectly performed software update: power was interrupted, or a problem in Wi-Fi (update should only be done via wire). Then the module becomes a pile of rubbish. Public recovery instructions are available.

ASUS

The ASUS official website provides customers with the Firmware Restoration utility (visit the download page of the purchased model).

1. Select desired version operating system.
2. Download the software, unzip the archive.
3. Connect the cord to the router.
4. Turn off the router.
5. Click the Restore button.
6. Hold for 5 seconds.
7. Without releasing, turn on the device.
8. The power indicator LED should start blinking slowly.
9. Open Connection Properties (Network and Sharing Center → Adapter Properties).
10. Set the IpV4 IP address to 192.168.1.10, subnet mask to 255.255.255.0.
11. Run the downloaded utility.
12. Specify the local path of the firmware to be uploaded (stock up on a fresh one in advance).
13. Click Upload.
14. Drink tea patiently.
15. A message appears: The system has been successfully updated. Wait for the reboot to finish.
16. The power indicator LED will turn on steadily. The recovery process is over.

Zyxel provides the Keenetic recovery utility. New third-party techniques are constantly being identified. The real problems will begin for those who used cellular 4G ...

In the 21st century, it is difficult to imagine life without the Internet. Internet access is available in almost all everyday places: at home, at work, in shopping malls, airports, etc. The number of users is growing every year world wide web and in particular users mobile devices(smartphones, tablets, laptops). Internet access on such devices is provided using a special 802.11 protocol or the more common name - Wi-Fi. The standard was developed in 1999 and is now very popular in the world, as it allows you to use the Internet without wires.

A large number of devices support this standard. Now wifi receivers There are in phones, and in TVs, and even in refrigerators. The ability to connect to wireless networks is provided by special devices - wi-fi routers. In fact, not only they, there are also wifi adapters, repeaters, amplifiers, etc. But the router is one of the most popular, and the principle of operation for all these devices is the same. Therefore, the router will be discussed in more detail later.

wifi router- this is a special device that has access to the external Internet (usually by wire) and provides wireless connection for local devices.

These devices are varied. Home routers (or routers) can be purchased for 500 rubles. For work and business, devices are needed more powerful, with large quantity functions. For such devices, you need to pay an order of magnitude, or even two orders of magnitude more money.

Home routers, for the most part, are very similar. One of the most popular is TP-LINK TL-WR-841. Let's take a closer look at what this device is and how it works.

Wi-Fi router basic settings

Wi-Fi router is small device equipped with special antennas. They may be external.

or internal

In order to ensure secure connection to wi-fi, the router has a number of characteristics and settings.

SSID is the name wifi networks. It can be public, i.e. available to everyone. But for protection, it is often hidden and you need to specify it manually.

The password is special code, which must be entered to connect to the router. In some cases, no password is set (for example, in public places). But recently, anonymous access to wireless networks has been banned, so there are practically no points left without a password.

From the user's point of view, these are the two main parameters, knowing which you can connect to the network. So how do you set up a Wi-Fi router?

Entering the Wi-Fi Router Settings

Each router has a special interface for configuration. There are several ways to get into it.

• The router comes with a CD special utility, which will help you open the setup interface and configure the router step by step
• You can enter the settings manually

We will not dwell on the first option, because it's pretty obvious. Its disadvantage is that it only works with newly purchased routers. If the router is already configured and has non-standard password, the disk will no longer help.

Let's take a closer look at the second option. There are also several cases here.

New router, just bought.

configured router.

The instructions are exactly the same as for the first option. The only difference is in point 3. Most likely, the information from the sticker is no longer suitable. You need to know the password from the router, otherwise you will not be able to get into it.

You have learned how to enter the router settings. Read about how to set it up on the pages of our website!